Nobles Strive 9000503 Скачать руководство пользователя страница 22

Страница: 22 / 52

OPERATION

Nobles Strive (09--04)

TROUBLESHOOTING -- Continued

PROBLEM

CAUSE

SOLUTION

Scrub head will not lower.

Wire #47 is not connected to batteries.

Connect wire #47 to battery as shown

in battery cable connection label.

Low voltage interrupter activated.

Recharge batteries.

No solution spray or solution spray

is ne en (Streaking occ rs)

Control grips not rotated.

Rotate control grips to activate spray.

is uneven (Streaking occurs).

Empty solution tank.

Refill solution tank.

Wrong rear vacuum shoe installed.

Install correct vacuum shoe.

Plugged spray tips.

Clean spray tips.

Spray tip pattern out of alignment.

Realign spray tips.

Plugged solution tank filter.

Clean solution tank filter.

Clogged solution line.

Flush plumbing system.

Faulty pump or solenoid.

Contact Service Center.

Scrub head continues to disperse

water when using accessory tools.

Rear ReadySpace vacuum shoe is

installed on scrub head.

Replace with extractor vacuum shoe.

Poor water pickup.

Full recovery tank.

Drain recovery tank.

Worn ReadySpace rollers.

Replace rollers.

Clogged vacuum shoes.

Clean vacuum shoes.

Wrong rear vacuum shoe installed.

Install correct vacuum shoe.

Clogged float shut-off screen inside

recovery tank.

Clean screen.

Loose recovery tank drain hose cap.

Tighten cap.

Loose or disconnected vacuum hose.

Connect hose cuffs securely.

Clogged vacuum hose.

Remove clogged debris.

Defective vacuum hose.

Replace vacuum hose.

Recovery tank lid is not in place.

Properly position lid.

Worn tank lid gasket.

Replace gasket.

Excessive foam/cream appears

on the floor during ReadySpace

cleaning.

Cleaning detergents were added to

solution tank.

Drain and rinse out solution tank and

refill with water only, do not add clean-

ing detergents.

Unable to adjust brush pressure

t i th

Worn extractor brushes.

Replace brushes.

meter in the green zone or meter

shows no reading.

Tripped circuit breaker.

Reset brush circuit breaker button.

shows no reading.

Loose or broken front brush motor belt.

Contact Service Center.

Short run time.

Low battery charge.

Charge batteries.

Defective batteries.

Replace batteries.

Batteries need maintenance.

See BATTERY MAINTENANCE.

Faulty charger.

Repair or replace battery charger.

Содержание Strive 9000503





















































Результаты поиска

Содержание Strive 9000503

Отзывы:

Nobles Strive 9000503, Руководство оператора и каталог запасных частей, Страница: 22 / 52

Результаты поиска

Содержание Strive 9000503

Отзывы: