3 of 3
nPP16 ER EFP
UL-924 EMER. RELAY PACK
FAMILY
INSTRUCTIONS
Acuity Brands | One Lithonia Way Conyers, GA 30012 Phone: 800.535.2465 www.acuitycontrols.com © 2018 Acuity Brands Lighting, Inc. All rights reserved. Rev.
01/26/2019
IS-NPP16ER-EFP-00
4
A-LEVEL PROGRAMMING INSTRUCTIONS
Please read all 3 steps before programming
1. Enter a specific programming function by pressing button the number
of times as the desired function number from the A-Level Detailed
Function Tables (e.g., press 23 times for function 23, Occupied Bright
Level).
2. LED will flash back the selected function’s current setting (e.g.,
11 times for 100%). To change setting, proceed to step 3 before flash
back sequence repeats 3 times. To exit the current function or to
change to a different function, wait for sequence to repeat 3 times
then return to step 1.
3. Press button the number of times indicated in the particular function’s
detailed table for the NEW desired setting. As confirmation of setting
change, LED flashes back the NEW setting 3 times before exiting.
27
= Relay Always On
Forces relay to stay closed even in off state
1
No*
2
Yes
28
= Dimming Always On
Maintains unoccupied dim level when in off state. Does not affect relay.
1
No*
2
Yes
29
= Occupancy Expiration of Manual Off
When enabled, operation of device will revert from a push-button
triggered override off state to Normal mode once the Occupancy Time Delay
(adjustable via SensorView or push-button) expires. Not used with Manual
On operating modes.
1
Disable*
2
Enable
Operational settings can be changed via the push-button sequence outlined below and right. Addtional settings can also be configured via SensorView software.
A-LEVEL DETAILED FUNCTION TABLES
17
= Secondary
Zone Dimming Offset
Percentage voltage difference of unit’s dimming output from primary
dimming output (Function 26, Follow Photocell Mode, must be
enabled)
1
-
100%
8
-30%
15
40%
2
- 90%
9
-20%
16
50%
3
- 80%
10
-10%
17
60%
4
- 70%
11
0%*
18
70%
5
-60%
12
10%
19
80%
6
-50%
13
20%
20
90%
7
-40%
14
30%
21
100%
23
= Occupied Bright Level
The percentage of the controllable dimming range that the dimming
output rises to when occupancy is detected. Setting is not applicable
if Follow Photocell Mode is enabled. Note: Adjusting the dim level
using a WallPod changes this setting when Follow Photocell Mode
is disabled.
1
1%
5
40%
9
80%
2
10%
6
50%
10
90%
3
20%
7
60%
11
100%*
4
30%
8
70%
24
= Unoccupied Dim Level
The percentage of the controllable dimming range that a dimming
output drops the lights to after the Idle Time Until Dim timer expires
1
1%*
5
40%
9
80%
2
10%
6
50%
10
90%
3
20%
7
60%
11
100%
4
30%
8
70%
26
= Follow Photocell Mode
Directs how a device’s dimming output reacts relative to a photocell
(ADC)
1
Disable*
2
Enabled (- only)
3
E/-
B-LEVEL PROGRAMMING INSTRUCTIONS
Please read all 4 steps before programming
1. Enter B-Level programming mode by holding down button until LED
flashes rapidly, release, hold down until rapid flash again, release, then
immediately enter programming function as described in step 2.
2. Enter a programming function by pressing button the number of
times as the desired function number from the table labeled B-Level
Functions (e.g., 12 times for function 12, Occupancy Tracking Channel).
3. LED will flash back the selected function’s current setting (e.g., 1 flash
for channel 1). To change setting, proceed to step 4 before flash
back sequence repeats 3 times. To exit the current function or to
change to a different function, wait for sequence to repeat 3 times
then return to step 1.
4. Press button the number of times indicated in the particular function’s
detailed table for the NEW desired setting (e.g., press 2 times for channel
2). As confirmation of setting change, LED flashes back the NEW setting 3
times before exiting.
B-LEVEL DETAILED FUNCTION TABLES
12
= Occupancy Tracking Channel
The local channel on which a device’s relay and/or dimming output
receives occupancy information
1 - 16
(e.g.,
1
= Channel 1*,
2
= Channel 2; etc.)
14
= Photocell Tracking Channel
The local channel on which a device’s relay and/or dimming output
receives photocell information
1 - 16
(e.g.,
1
= Channel 1*,
2
= Channel 2; etc.)
16
= Switch Tracking Channel
The local channel on which a device’s relay and/or dimming output
receives switch information.
1 - 16
(e.g.,
1
= Channel 1*,
2
= Channel 2; etc.)
Note: Normal default is channel 1, units with SW2 and SA2 options are
defaulted to channel 2
17
= Override (Relay / Dimming)
Indicates whether a device’s relay is forced on/off and/or dimming
output is forced to max/min
1
Not forced*
2
Override On
3
Override Off
18
= Special Operating Mode
Unique defined behaviors of relays and/or dimming outputs, see right
for function definitions
1
Normal*
5
Predictive Off
2
Manual On
6
Manual to Override On
3
Auto to Override On
7
Manual to Normal
4
Manual to Full Auto On
19
= Invert Relay Logic
Reverses functionality of relays
1
Normal Logic*
2
Inverse Logic
21
= WallPod Dimming Adjustments
Defines whether user dimming adjustments are maintained after
lights are cycled, whether they revert to default levels, or whether they
temporarily disable a connected dimming photocell (until lights cycle)
1
Permanent*
2
Temporary
3
Photocell Temp
Override
22
= Maintain Dim Level when Vacant
Prevents lights from turning fully off once in unoccupied state
1
No*
2
Yes
23
= Special Switch Tracking Mode
Defines unique behavior related to how relays respond to particular
switch information
1
Disable*
3
Ignore Ons
2
Ignore Offs
4
Ignore Ons & Offs
31
= High End Trim**
Maximum voltage level of the device’s dimming output. Commonly used for
task tuning where absolute light level is not to be increased via a Wallpod
or scene. When output is at high end trim, the reported control percentage
will be 100%. Corresponding lumen output % is dependent on ballast/
driver capabilities.
1
0.7 V
4
3V
7
6V
10
9V
2
1V
5
4V
8
7V
11
10V
3
2V
6
5V
9
8V
32
= Low End Trim**
Minimum voltage level of the device’s active dimming range. Level can not
be reduced via a WallPod or scene. When output is at low end trim, the
reported control percentage will be 1%. Corresponding lumen output % is
dependent on ballast/driver capabilities.
1
0.7 V
4
3V
7
6V
10
9V
2
1V
5
4V
8
7V
11
10V
3
2V
6
5V
9
8V
** Setting precision of 0.1V is available via SensorView. Device status LED
blinks out current value rounded to nearest selection above.
FUNCTION 18 DEFINITIONS
NORMAL
Operating Mode where occupancy sensors are capable of turning lights
both on/off
AUTO TO OVERRIDE ON
Special Mode where lights are turned on initially by occupant detection but
then left in the Override On state
MANUAL ON TO FULL AUTO
Special Mode that initially requires the occupant to manually turn on the
lights, after which the sensor assumes full on/off control
MANUAL ON
Special Mode that always requires the occupant to manually turn the
lights on, while having them turn off automatically by a sensor (default on
models with SA and SA2 options)
PREDICTIVE OFF
When lights are switched off, this Special Mode determines whether
occupants remained or left the room, so as to leave the lights in either the
Override Off or Auto On state
MANUAL TO TIMED OVERRIDE ON
Special Mode where lights are initially turned on manually but remain in
the Override On state for a pre-determined period (Timed Override Delay)
MANUAL TO NORMAL
Special Mode where lights are initially turned on manually but remain in
the Normal State (enabling auto-dimming) for a pre-determined period
(Timed Override Delay)
* indicates default setting for base
nPP16 (D) ER EFP models.
NOTE
For further troubleshooting guidance, please contact the Controls Technical Support Team
1(800)-535-2465