Attention: Always add water
fi
rst to the 0.7 l mark and then the descaling agent. Never vice versa!
Please follow the manufacturer’s instructions on how to use the descaler.
£
Only now add the descaler.
The display shows “HOSE ON SPOUT AND IN DRIP TRAY”.
£
Connect one end of the hose to the height-adjustable spout (
fi
g. 7).
£
Connect the other end of the hose to the back of the drip tray on the right (
fi
g. 10).
£
Press the rotary control
or
touch CONTINUE.
The display shows “START DESCALING”.
£
Place a suf
fi
ciently large bowl (at least 0.5 l) centrally underneath the spout (
fi
g. 1/E).
£
Press the rotary control
or
touch START.
The appliance starts the descaling process. The display shows “SYSTEM DESCALING, DO NOT
REMOVE HOSE”. The descaling process is automatic and takes approximately 30 minutes. The
descaling solution is passed at intervals through the system.
Once the descaling cycle is completed, the display shows “EMPTY TRAYS”.
£
Remove the drip tray and the used coffee container (
fi
g. 1/N and 1/O) and empty both.
£
Reinsert the drip tray and used coffee container.
£
Remove the water tank and rinse it with fresh water.
£
Reinsert the
fi
lter into the water tank if required.
£
Fill the water tank with fresh water and reinsert it.
The display shows “HOSE ON SPOUT AND IN DRIP TRAY”.
£
Connect the hose with one end to the height-adjustable spout (
fi
g. 7).
£
Connect the other end of the hose to the back of the drip tray on the right (
fi
g. 10).
£
Place a suf
fi
ciently large bowl (at least 0.5 l) centrally underneath the spout (
fi
g. 1/E).
£
Press the rotary control
or
touch CONTINUE.
The display shows “PLEASE RINSE”.
£
Press the rotary control
or
touch START to start the rinsing process.
The display shows “SYSTEM RINSING, DO NOT REMOVE HOSE”. The automatic cleaning process
is started and lasts for approximately three minutes. Once the cycle is
fi
nished, the display shows
“EMPTY TRAYS”.
£
Empty the drip tray and used coffee container (
fi
g. 1/N and 1/O) and reinsert them both when
cleaned.
The appliance reheats and is ready for use. The display shows the main menu.
Attention: Please immediately remove any descaler residues from the casing with a damp cloth.
5.6. Regular manual cleaning
Note: Please follow these cleaning instructions. Working with foodstuffs demands the highest stand-
ards of cleanliness.
Attention: Never immerse the appliance in water! Do not use abrasive cleaning agents.
£
Only use a soft, damp cloth without any detergent for cleaning the casing inside and out.
Note: To clean the display while the appliance is running, you can lock the display by selecting
“MAINTENANCE”, “DISPLAY MAINTENANCE” and press the rotary control. Press again to unlock the
display.
£
Empty the drip tray (
fi
g. 1/N) and used coffee container (
fi
g. 1/O) at the latest when this is indi-
cated on the display (only when the appliance is switched on!).
Note: When cleaning the drip container (
fi
g. 1/N) make sure that the two metal contacts and the space
between them are always clean and dry! Use soapy water every now and again to clean.
£
The water tank should be rinsed daily with clear water and then be re-
fi
lled daily with fresh cool
water.
Note: Dried milk residue is dif
fi
cult to remove.
£
Therefore clean frother, hose and spout regularly.
Note: From time to time (ideally when the appliance will not be used for a while, but at any rate at
regular intervals!) the frother needs to be completely dismantled and thoroughly cleaned under running
water.
£
Remove the cover (
fi
g. 1/P) at the bottom of the height-adjustable spout.
£
Pull the frother down and out (
fi
g. 11) and dismantle it completely (
fi
g. 1/R).
£
Clean the components (
fi
g. 1/R) thoroughly and reassemble the frother.
£
Reinsert the assembled frother into the height-adjustable spout (
fi
g. 11).
£
Replace the cover on the height-adjustable spout (
fi
g. 1/P)
Note: Your appliance is equipped with back rollers (
fi
g. 1/Q). They allow you to move the appliance on
a
fl
at working top. This way, you can also clean the space underneath the appliance.
5.7. Cleaning the brew unit
Attention: Remove the brew unit only when the appliance is switched off.
Attention: Clean the brew unit after each cleaning cycle, but at least once a month. Otherwise your
warranty could be compromised.
When necessary the brew unit can be removed and cleaned under cold, running water. Never use
cleaning agent, clear, cold water only! For reasons of hygiene we recommend the removal and clean-
ing of the unit thoroughly after each run of the cleaning programme (see 5.4.).
£
Open the service door on the right of the casing (
fi
g. 1/L) by pulling the inner handle slightly
towards you and carefully move the service door away from casing.
£
Remove the brew unit by pressing the red switch upward and turning the handle all the way to
the left until it snaps into place (
fi
g. 12).
£
Carefully remove the brew unit using the handle.
£
Clean the brew unit under running water and let it dry.
£
Reinsert the brew unit carefully and lock it by pressing down the red switch and turning the
handle.
£
Close the service door and in doing so carefully place the pivots at the back of the door into the
notches. Make sure that the door (
fi
g. 1/L) completely snaps back into place.
5.8. Changing the
fi
lter
The
fi
lter will need to be changed after about 50 l of water have been drawn. The display shows
“CHANGE FILTER”.
You can still make coffee, but we recommend changing the
fi
lter immediately.
£
Turn the rotary control to “SETTINGS” and press it
or
touch the Settings symbol.
£
Turn the rotary control to “FILTER” and press it.
£
Turn the rotary control to “INSERT FILTER? YES”, so the appliance recognizes the new
fi
lter.
£
Empty the water tank (
fi
g. 1/F and 2) and unscrew the
fi
lter carefully, using the integrated tool at
the end of the measuring spoon (
fi
g. 4).
£
Discard the
fi
lter.
£
Press the rotary control.
The display shows “INSERT FILTER” or “FILTER INSERTED” in case the
fi
lter has already been
replaced.
96
97
GB
GB
5. Cleaning and maintenance
5. Cleaning and maintenance
