Niveo NGSME48T4H Скачать руководство пользователя страница 226

Страница: 226 / 338

Chapter

3: Web Management

DHCP - Snooping Table

PoE Switch User Manual | 226

3.2.4.2. DHCP - Snooping Table

This page display the dynamic IP assigned information after DHCP Snooping mode is

disabled. All DHCP clients obtained the dynamic IP address from the DHCP server will be

listed in this table except for local VLAN interface IP addresses. Entries in the Dynamic DHCP

snooping Table are shown on this page.

Navigating the DHCP snooping Table

Each page shows up to 99 entries from the Dynamic DHCP snooping table, default being 20,

selected through the "entries per page" input field. When first visited, the web page will show

the first 20 entries from the beginning of the Dynamic DHCP snooping Table.

The "MAC address" and "VLAN" input fields allows the user to select the starting point in the

Dynamic DHCP snooping Table. Clicking the Refresh button will update the displayed table

starting from that or the closest next Dynamic DHCP snooping Table match. In addition, the

two input fields will - upon a Refresh button click - assume the value of the first displayed

entry, allowing for continuous refresh with the same start address.

The >> will use the last entry of the currently displayed table as a basis for the next lookup.

When the end is reached the text "No more entries" is shown in the displayed table. Use the

|<< button to start over.

DHCP snooping Table Columns

MAC Address

User MAC address of the entry.

VLAN ID

VLAN-ID in which the DHCP traffic is permitted.

Source Port

Switch Port Number for which the entries are displayed.

IP Address

User IP address of the entry.

IP Subnet Mask

User IP subnet mask of the entry.

DHCP Server Address

DHCP Server address of the entry.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды