Niveo NGSME48T4H Скачать руководство пользователя страница 166

Страница: 166 / 338

Chapter

3: Web Management

VCL - MAC-based VLAN

PoE Switch User Manual | 166

3.1.17. Configuration - VCL

3.1.17.1. VCL - MAC-based VLAN

The MAC-based VLAN entries can be configured here. This page allows for adding and

deleting MAC-based VLAN entries and assigning the entries to different ports. This page

shows only static entries.

Delete

To delete a MAC-based VLAN entry, check this box and press save. The entry will be deleted

on the selected switch in the stack.

MAC Address

Indicates the MAC address.

VLAN ID

Indicates the VLAN ID.

Port Members

A row of check boxes for each port is displayed for each MAC-based VLAN entry. To include

a port in a MAC-based VLAN, check the box. To remove or exclude the port from the

MAC-based VLAN, make sure the box is unchecked. By default, no ports are members, and

all boxes are unchecked.

Adding a New MAC-based VLAN

Click

“

Adding New Entry

” to add a new MAC-based VLAN entry. An empty row is added to

the table, and the MAC-based VLAN entry can be configured as needed. Any unicast MAC

address can be configured for the MAC-based VLAN entry. No broadcast or multicast MAC

addresses are allowed. Legal values for a VLAN ID are 1 through 4095.

The MAC-based VLAN entry is enabled on the selected stack switch unit when you click on

"Save". A MAC-based VLAN without any port members on any stack unit will be deleted when

you click "Save".

The

“

Delete

” button can be used to undo the addition of new MAC-based VLANs. The

maximum possible MAC-based VLAN entries are limited to 256.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды