Niveo NGSM48T2 Скачать руководство пользователя страница 259

Страница: 259 / 355

Chapter 5: Monitor, Diagnostic, Maintenance

Monitor, Diagnostic, Maintenance

NGSM48T2 User Manual | 259

Monitor

Monitor / System

Monitor / System / Information

The switch system information is provided here.

Contact

The system contact configured in Configuration | System | Information | System

Contact.

Name

The system name configured in Configuration | System | Information | System

Name.

Location

The system location configured in Configuration | System | Information | System

Location.

MAC Address

The MAC Address of this switch.

Chip ID

The Chip ID of this switch.

System Date

The current (GMT) system time and date. The system time is obtained through the

configured NTP Server, if any.

System Uptime

The period of time the device has been operational.

Software Version

The software version of this switch.

Software Date

The date when the switch software was produced.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды