Niveo NGSM48T2 Скачать руководство пользователя страница 169

Страница: 169 / 355

Chapter 3: Featuring Configuration

– Web UI

Featuring Configuration

– Web UI

NGSM48T2 User Manual | 169

QoS

QoS / Ingress Port Classification

This page allows you to configure the basic QoS Ingress Classification settings for

all switch ports.

The settings relate to the currently selected stack unit, as reflected by the page

header.

The displayed settings are:

Port

The port number for which the configuration below applies.

QoS class

Controls the default QoS class, i.e., the QoS class for frames not classified in any

other way. There is a one to one mapping between QoS class, queue and priority. A

QoS class of 0 (zero) has the lowest priority.

DP level

Controls the default Drop Precedence Level i.e., the DP level for frames not

classified in any other way.

PCP

Controls the default PCP for untagged frames.

DEI

Controls the default DEI for untagged frames.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды