Niveo NGSM48T2 Скачать руководство пользователя страница 166

Страница: 166 / 355

Chapter 3: Featuring Configuration

– Web UI

Featuring Configuration

– Web UI

NGSM48T2 User Manual | 166

Voice VLAN Configuration

Voice VLAN / Configuration

The Voice VLAN feature enables voice traffic forwarding on the Voice VLAN, then

the switch can classify and schedule network traffic. It is recommended that there be

two VLANs on a port - one for voice, one for data. Before connecting the IP device to

the switch, the IP phone should configure the voice VLAND ID correctly. It should be

configured through its own GUI.

Mode

Indicates the Voice VLAN mode operation. We must disable MSTP feature before

we enable Voice VLAN. It can avoid the conflict of ingress filtering. Possible modes

are:

Enabled:

Enable Voice VLAN mode operation.

Disabled:

Disable Voice VLAN mode operation.

VLAN ID

Indicates the Voice VLAN ID. It should be a unique VLAN ID in the system and

cannot equal each port PVID. It is a conflict in configuration if the value equals

management VID, MVR VID, PVID etc. The allowed range is 1 to 4095.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды