Nissin MG8000 Extreme Скачать руководство пользователя страница 8

Страница: 8 / 11

Single Group Slave Flash (Group A Setting)

1. Navigate the cursor to

Group A

2. Navigate the cursor to

Flash mode

and select mode: TTL or M

Selecting TTL

1. Navigate the cursor to the

Value Adjustment

and set the EV

compensation level.
2. Navigate the cursor to M (Master).
3. Select TTL or --- (flash-off) in the

Flash Mode

4. When TTL mode selected, move the cursor to the

Value Adjustment

and

set the EV compensation level.
5. Navigate the cursor to M (Master).
6. Select TTL or --- (FLASH OFF) in the

Flash Mode

7. When TTL mode selected, Navigate the cursor to the

Flash Adjustment

and set the power ratio.

Selecting M

1. Navigate the cursor to the

Flash Adjustment

and set the power ratio

2. Navigate the cursor to M (Master).
3. Select M or --- (FLASH OFF) in the

Flash Mode

4. When M mode selected, navigate the cursor to the

Flash Adjustment

and set the power ratio.

Note: When setting --- (FLASH OFF) mode, the master flash may flash when
shutter released. This flash is however the monitoring flash (pre-flash) before the
camera’s shutter opens and is not be exposed in the actual picture.

Multiple Group Slave Flash (Group B & C Setting)

Group A

MUST

be set, in order to add Group B

Adding Group B

When TTL mode selected in Group A

1. Navigate the cursor to GROUP B, and select TTL in the operation mode
box.

2. Navigate the cursor to

Flash Adjustment

and select the power level ratio

between Group A and Group B.
^The power level ratio can be selected from 13 different combinations, such
as A:B = 8:1 – 5.6:1 – 4:1 – 2.8:1 – 2:1 – 1.4:1 – 1:1 – 1:1.4 – 1:2 – 1:2.8 –
1:4 – 1:5.6 and 1:8
3. Navigate the cursor to M (Master).
4. Select TTL or --- (flash-off) in the

Flash Mode

5. When TTL mode selected, navigate the cursor to the

Flash Adjustment

and

set the EV Compensation.

When M mode selected in Group A

1. Navigate the cursor to GROUP B, and select M in the operation mode box.
2. Navigate the cursor to

Flash Adjustment

and select the power ratio

3. Navigate the cursor to M (Master).
4. Select M or --- (flash-off) in the

Flash Mode

5. When M mode selected, navigate the cursor to the

Flash Adjustment

and set the power ratio..

Adding Group C

Group A & B (A:B)

MUST

be set, in order to add Group C.

^The group C is independently set out from the power ratio combination.

When TTL Mode selected in Group A & B:

1. Navigate the cursor to GROUP C, and select TTL in the

Flash Mode

2. Navigate the cursor to

Flash Adjustment

and select the EV compensation.

3. Navigate the cursor to M (Master).
4. Select TTL or --- (flash-off) in the

Flash Mode

5. When TTL mode selected, navigate the cursor to the

Flash Adjustment

and

set the EV Compensation.

When M Mode selected in Group A & B:

1. Navigate the cursor to GROUP C, and select M in the

Flash Adjustment

2. Navigate the cursor to

Flash Adjustment

and select the power ratio.

3. Navigate the cursor to M (Master).

4. Select M or --- (flash-off) in the

Flash Mode

5. When M mode selected, navigate the cursor to the

Flash Adjustment

and set the power ratio.
^This 3 group slave flash technology is recommended to shade off or remove the
shadow behind subject which may be caused by the lighting produced by Group
A and/or B.

The modes available on the Master flash are TTL and M mode.
The master flash sets the signal transmission channel, flash reflector zooming
position, flash mode of the master flash itself and flash mode and value
adjustment of the slave flash at A, B and C respectively.

Setting the Master flash

In the main page

Select Wireless mode.

In the Wireless page

Select Master mode.

In the Master page

Navigate the cursor and adjust the value according to the
instruction at the bottom bar.

Cursor Navigation

Value Adjust

Channel Select

Select Channel: Ch1, Ch2, Ch3 & Ch4

Zoom Select