background image

2.3 Development Kit Configuration 

This development kit may be used as a stand alone development kit interfaced to a 
PC or as a shield connected to another development kit with a compatible Arduino 
shield interface.  

The SW1 DIP switch will ship with a piece of tape covering the switches. This should 
be removed by the user upon getting started with the kit.  

2.3.1 USB Interfaces 

The development kit has two USB Mini-B connectors to allow for the use of the 
modem's serial UART AT command interface and/or the modem's USB interface. 

The J5 USB interface is for connecting to the modem's USB interface. The USB 
interface will allow customers to connect to multiple different communication ports on 
the modem including: 

-

AT Command interfaces 

-

Debug interfaces for modem diagnostic tools 

-

GNSS NMEA streaming interfaces 

The specific USB interfaces available will be modem specific and connecting to the 
USB interface will require that users download the modem's USB drivers from its 
product page.  

The J14 interface will connect to the modem's USB to serial UART interface IC to 
access the modem's serial UART interface. The USB to serial UART interface IC used 
on the J14 USB interface is an FTDI FT234XD. The FTDI drivers for the FT234XD are 
available on 

FTDI's website

2.3.2 UART Selection 

The Skywire modem's UART interface is multiplexed to several different interfaces on 
the development kit to allow for easy interfacing with different host development kits 
and for accessing it through the USB to serial UART interface (J14).  

The USB to serial interface will be automatically selected when a USB connection is 
powered on J14 and will override the selection switch for the other UART interfaces. 
This feature may be bypassed, if desired, by modifying the circuit board. 

 

PN 1002634 REV 1

© NimbeLink Corp. 2021. All rights reserved.

Содержание NL-SWDK2






























Отзывы: