Nilfisk-ALTO C 100.4 Скачать руководство пользователя страница 13

13

7 Trouble-shooting

To avoid unnecessary disappointments, you should check the following before contacting the Nilfi sk 
service organization:

Symptom Cause 

Recommended 

action

Machine refuses to start

  Machine not plugged in 

Plug in machine.

 

Defective socket 

Try another socket.

 

Fuse has blown 

Replace fuse. Switch off other machines.

 

Defective extension cable 

Try without the extension cable.

Fluctuating pressure 

Pump sucking air 

Check that hoses and connections are air- 

   tight.
 

Valves dirty, worn out  

Clean and replace or refer to local Nilfi sk  

 or 

stuck 

distributor

 

Pump seals worn out 

Clean and replace or refer to local Nilfi sk-  

   distributor.

Machine stops

 

Fuse has blown  

Replace fuse. Switch off other machines. 

 

Incorrect mains voltage 

Check that the mains voltage corresponds  

 

 

to specifi cation on the model tag.

 

Thermal sensor activated 

Leave the washer for 5 minutes to cool   

   down.
 

Nozzle partially blocked 

Clean the nozzle (see section 6.2)

Fuse blows

 

Fuse too small 

Change to an installation higher than the  

 

 

amp. consumption of the machine. 

 

 

You may try without the extension cable.

Machine pulsating

 

Air in inlet hose/pump 

Allow machine to run with open trigger until  

 

 

regular working pressure resumes.

 

Inadequate supply of  

Check that the water supply corresponds to 

 

mains water 

specifi cations required (see model tag) 

 

 

NB!

 Avoid using long, thin hoses (min. 1/2")

 

Nozzle partially blocked 

Clean the nozzle (see section 6.2)

 

Water fi lter blocked 

Clean the fi lter (see section 6.1)

 

Hose kinked 

Straighten out hose.

Machine often starts 

Pump/spray gun is 

Contact your nearest Nilfi sk Service 

and stops by itself 

leaking Centre.

Machine starts, but 

 

Pump/hoses or accessory 

Wait for pump/hoses or accessory to thaw.

no water comes out 

 frozen

 

No water supply  

Connect inlet water.

 

Water fi lter blocked 

Clean the fi lter (see section 6.1)

 

Nozzle blocked 

Clean the nozzle (see section 6.2)

In case problems other than the above occur, please contact your local Nilfi sk distributor.

Содержание C 100.4



















Отзывы: