manualshive.com logo in svg

Nilfisk-Advance 56508769, Руководство по обслуживанию, Страница: 4 / 26

Поделиться
Скачать
Nilfisk-Advance 56508769 Скачать руководство пользователя страница 4

2

 - FORM NO. 56043123 - SR 1900

 CAUTIONS 

AND 

WARNINGS

 SYMBOLS

Nil

fi

 sk uses the symbols below to signal potentially dangerous conditions.  Read this information carefully and take the necessary 

steps to protect personnel and property.

 DANGER!

Is used to warn of immediate hazards that will cause severe personal injury or death.

 WARNING!

Is used to call attention to a situation that could cause severe personal injury.

 CAUTION!

Is used to call attention to a situation that could cause minor personal injury or damage to the machine or other property.

  Read all instructions before using.

GENERAL SAFETY INSTRUCTIONS

Speci

fi

 c Dangers, Warnings and Cautions are included to warn you of potential danger of machine damage or bodily harm.

 DANGER!

This machine emits exhaust gases (carbon monoxide) that can cause serious injury or death.  Always provide adequate ventilation 
when using machine.

 WARNING!

Remove all jewelry when working near electrical components.



Turn the key switch off (O) and disconnect the battery before servicing electrical components.



Never work under a machine without safety blocks or stands to support the machine.



Do not dispense 

fl

 ammable cleaning agents, operate the machine on or near these agents, or operate in areas where 

fl

 ammable 



liquids exist.

 CAUTION!

Before performing any service function, carefully read all instructions pertaining to that function.



Do not leave the machine unattended without 

fi

 rst turning the key switch off (O), removing the key and securing the machine.



Turn the key switch off (O) and remove the key before changing the brooms and before opening any access panels.



Take precautions to prevent hair, jewelry or loose clothing from becoming caught in moving parts.



Close and secure all doors, covers and access panels as shown in the SR 1900 Instructions For Use before using the machine.



Do not clean the cab with a pressure washer.  We recommend hand-washing the cab using normal “garden hose” water pressure.  



Do not spray water directly at or into the cab 

fi

 lter or any electrical components.  Allow the machine to dry completely before use.

SAVE THESE INSTRUCTIONS

Содержание 56508769



























Отзывы:

Нет отзывов