background image

 8

 - FORM NO. 56091105 - BU800

EN

ENGLISH

MAINTENANCE

A

AFTER USE

After working, before leaving the machine:

1

  Store the machine in a clean and dry place, indoors only.  

2

  Park the machine on a level 

fl

 oor. Ensure once the machine is 

left unattended it is secured against unintentional movement.

3

  Turn the Key Switch

 (1)

 to the OFF position (O).

4

  Remove the key from the machine to prevent unauthorized use 

of the machine.

5

  Perform the daily maintenance procedures (see the Mainte-

nance schedule).

MAINTENANCE SCHEDULE

Maintenance Item 

Daily 

Monthly  Yearly

 Charge Batteries 

  x

  Check/Replace Dust Bags 

  x

 Check/Replace Skirt 

  x

 Clean Pad 

  x

 Lubrication 

   

  x

  Check/Service Pad Motor Brushes 

   

  x

  Service Drive Motor Brushes 

   

   

  x

BATTERY MAINTENANCE

Charge the batteries each time the machine is used for 1 hour or 

longer, or whenever the Battery Meter reads in the red area.

To Charge the Batteries...

1

 Remove cover.

2

  Plug charger in.

3

 Check the 

fl

 uid level in all battery cells after charging the batteries.  

Add distilled water, if necessary, to bring the 

fl

 uid level up to the 

bottom of the 

fi

 ller tubes.

CAUTION!

To avoid damage to 

fl

 oor surfaces, wipe water and acid 

from the top of the batteries after charging.

CAUTION!

Acid can spill onto the 

fl

 oor if the batteries are over-

fi

 lled.

 IMPORTANT

Motor damage resulting from failure to service carbon brushes is not 
covered under warranty.  See the Limited Warranty statement.

SPECIFICATIONS

Model BU800 

51BT

Model Number

56383526

Power Supply

 36 

volt

Motor, Pad 

 1.5 kW  (2.0 hp) 55 amp

Motor Traction

 

.37 kW (.5 hp) PM

Drive System

 Direct 

Drive

Pad

51cm (20”)

Pad Speed

 1500 

rpm

Pad Pressure

 Automatic

Speed, Forward

 

0 - 73 m/min (0-240 ft/min)

Speed, Reverse

 

0 - 52 m/min (0-170 ft/min)

Vibration

 <7.6 

mm/s

Sound Level (dbA) 

68

Drive Wheel

 4cmx20cm 

(1.62”x8.00”)

On-board Charger

 

Standard 36V, 21A

-AC Input

 

100-240V ~ 50/60Hz 12-6A

Length

 

127cm (50 inches)

Width

 

58cm (23 inches)

Height

 

105cm (41.25 inches)

Burnishing Swath

 

51cm (20 inch)

Polishing Rate 

2230 sq. m/hr. (24,000 sq. ft/hr)

Weight (w/o batteries)

 

79 kg / 174 lbs.

Gross Vehical Weight (GVW)

 

233 kg / 515 lbs.

Gradeability - Cleaning (max.)

 2%

Содержание 56383526











Отзывы: