Installing the
Wall-Mount Volume
Control in your Wall
Carefully feed the Speaker
Cable back into the wall and
secure the Wall-Mount
Volume Control to the brack-
et using the supplied screws.
Then install the Decora®
faceplate using the
supplied faceplate screws.
(See Figure 9)
Mounting the
In-Wall Speakers
Be sure to observe proper
polarity when connecting
the Speaker Cable to the
In-Wall Speakers.
To install the In-Wall
Speakers, insert the Speaker
Bracket through the hole
and pull it forward so that its
front edge slides into the
hole and stops in place.
Attach the Speaker Frame to
the Speaker Bracket using
the supplied screws.
DO NOT OVERTIGHTEN
THE SCREWS. This will
distort the Frame and the
grilles will not fit (simply
loosen the screws and the
Grille may be installed).
Pull the Speaker Cable
through the hole and make
the connections to the
Speaker Baffle as shown in
Figure 8.
Connect the Speaker Baffle
to the Frame and conceal
the excess Cable inside the
wall. Screw the Baffle into
the Frame, and carefully
install the Grille.
The Grilles fit tightly to pre-
vent them from coming
loose over time. Some effort
and care may be required
when installing them.
Connect the wires:
Red = Right Positive (+)
Black = Right Negative (-)
White = Left Positive (+)
Green = Left Negative (-)
Figure 9
7
INSTALLATION
!
!
!
8
Connecting the
Speaker Cable to
your Equipment
If your receiver or amplifier
has both “Speakers A” and
“Speakers B” connections
on the rear of the chassis,
connect the Cable connect-
ed to the Speakers to “A”.
Be sure to observe proper
polarity when connecting
the Speaker Cable to your
equipment.
Connect the wires:
Red = Right Positive (+)
Black = Right Negative (-)
White = Left Positive (+)
Green = Left Negative (-)
Connecting
Additional Speakers
and Volume Controls
In order to listen to several
speaker pairs at the same
time, each run of Speaker
Cable (and their respective
Wall-Mount Volume Controls
and Speakers) must be
connected to your amplifier.
This is easily accomplished
by using standard wire nuts
and connecting the other
speaker pairs to your ampli-
fier in the following manner:
a) Simply cut a short
“pigtail” (approximately 12”)
of 4-conductor Speaker
Cable and remove 2” of the
outer sheath from both
ends. Strip 3/8” of the col-
ored insulation from each of
the four conductors at one
end, and connect this end to
your stereo amplifier’s out-
put terminals.
Connect the wires
Red = Right Positive (+)
Black = Right Negative (-)
White = Left Positive (+)
Green = Left Negative (-)
b) Strip 3/4" of insulation
from both the end of the
“pigtail” and from the end
of each of the incoming
Speaker Cable’s conductors.
c) Connect each of the
“pigtail’s” conductors to its
corresponding color on the
incoming Speaker Cable
feeds by twisting the wires
together and securing them
with a wire nut of the
appropriate size.
Protecting Your
Amplifier
The Wall-Mount Volume
Controls included in the
Music Anywhere! Kits
incorporate an “Impedance
Magnifying” feature to
protect your amplifier.
To set the “Magnification
Factor”, simply straddle the
small black “jumper” over
the appropriately marked
“jumper pins” for the correct
magnification setting based
on the number of speaker
pairs in your system.
(see Figure 10)
ADDING ON
SETTING THE MAGNIFICATION FACTOR
1 – 2 speakers pairs
set jumper on ..................... 2X
3 – 4 speakers pairs
set jumper on ..................... 4X
5 – 8 speakers pairs
set jumper on ..................... 8X
9 – 16 speakers pairs
set jumper on ................... 16X
16x
MAGNIFICATION
FACTOR
JP1 (LEFT)
(RIGHT) JP2
MAGNIFICATION
FACTOR
8x
4x
2x
16x
8x
4x
2x
Left
Jumper
Right
Jumper
Figure 10
