background image

Repeater Commissioning

Downlink gain setting

First the alarm LED only indicates the downlink input power level, here we use color of Alarm LED to adjust the gain of

the repeater. Alarm LED color must remain green. As for the downlink working performance, it is a good working point
that Alarm LED maintains “Green” color with the intention of turning orange; here we refer as “edge point”. At this time,
downlink output power and coverage effect are stable.

And the equipment must be as far as possible away from overloading status of “red” (the equipment would hold
higher interference and depression ability at this stage). So we shall try our best to set the equipment near “edge
point” of green and intention of turning orange during engineering.

Setting of “edge point”:

Switch on the power supply after connection with donor antenna and server antenna, and observe ALARM LED.

• If it shines “orange”, use 1dB as step to reduce the gain until “green” turns on, then increase the gain 1~3dB

attenuation value until “orange” starts to turn on, then brings back 1~2dB till “green” is on, then fix the gain
and the repeater’s downlink output power reaches the perfect status.

• If it shines “green” then:

Please check coverage effect firstly, if the coverage effect is good, the engineering has reached
expecting target, thus there is no need to do anything.

• To check whether the attenuation value has been set, if it is, use 1dB as step to increase gain until the

“orange” turns on, then brings back 1~2dB till “green” is on again , then the repeater’s downlink output power

reaches the perfect status.

• But if attenuation has not been set, it indicates that the input power is not strong enough to let the repeater

reach its good coverage.

If the coverage effect is not good, the donor antenna should be adjusted to get stronger input signal. It is
recommended that one person shall check the coverage effect inside the building when the other person is trying to

adjust the antenna or the repeater. At this stage, please make sure “Orange” color will not be generated by self

oscillation. Please take off the server antenna to check if it is self oscillation or not: if the Orange turns to be green, it
is self oscillation; if it stays as Orange, it is not self oscillation. Please follow steps in other page to turn Orange to be

Green.

Uplink gain setting

Standard: uplink attenuation values =downlink attenuation values

Remark

: Avoid putting more than a 5dB difference between the Uplink and Downlink. And Uplink gain must be equal to or

less than Downlink gain, it can’t be more in order to avoid interference with mobile network.

Questions & Solutions

What signal level in dBm is optimal for the correct booster functioning?

For the optimal functioning of the booster, the BS (input) readings should be between - 65 and 50 dBm. The MS (output
power) readings must be b05 and +15 dBm. Device Gain must be 65/65 dB. If the BS is lower than - 65dBm, the
coverage will be smaller. However, the device can work normally. If the BS is too weak, it'll be necessary to adjust the
position of the outdoor antenna by raising it as high as possible (on a pole on the rooftop) and pointing it towards the
provider's nearest base station. If the BS is higher than - 50 dBm, the device will have a self-excitation issue. In those
conditions, the output signal will drop during communications. If the two antennas are placed very close to each

Содержание NS-150























Отзывы: