Nikon ZOOM800, Инструкция по эксплуатации

Страница: 10 / 20

MAIN FEATURES
Powerful multi coated zoom lens with
lens elements
l
passive multi AF in 1024 measuring steps
High-power zoom flash for tele shooting
Easy to access
control with illuminator
Creative modes (Portrait, Action, Night Scene, Land-
scape, etc.
Compact and light weight body
BEFORE USING
A fast film such as 200 or 400 is recom-
mended to prevent blurriness and to obtain a longer
flash range.
When focusing is difficult or impossible, AF Monitor
blinks to warn you that an out-of-focus picture will
occur. Set Landscape mode or use Focus Lock func-
tion. (page 24, 29)
Do not hold the camera by the lens.
Before taking important pictures (at weddings, on
trips abroad, etc. ) test the camera and learn how it
works.
CAUTIONS
camera has a high voltage circuit. Because
it is dangerous, do not attempt to take the cam-
era apart.
18
For ZOOM800 QD only; The date display [ “00 0
blinks when the batteries are replaced.
pressing
either the Mode Button, Select Button, or Set But-
ton,
will be displayed. Reset the correct time
and date.
When replacing the batteries, do so as quickly as
possible to avoid erasing camera memory. We rec-
ommend replacing the batteries when there is no
film in the camera.
The batteries can explode or cause burns if dis-
posed of in fire or if shorted, disassembled,
heated or recharged.
l
Recommended Replacement 3V Lithium Batteries:
or equivalent X 2.
TURNING THE POWER ON/OFF
The power is turned on or off by selecting ON or OFF
on the Drive Dial.
(Fig. 6)
When the power is turned on, the lens moves from the
storage position to the wideangle position, and the cam-
era is set automatically lo the mode selected on the
Mode Dial.
CHECKING THE
When the batteries are nearly exhausted, will
appear on the LCD Panel. Replace new batter-
ies as soon as possible.
If the built-in flash does not operate, do not touch
the internal parts of the camera, as it contains a
high voltage circuit. Take the camera lo an au-
thorized Nikon dealer or service center.
ATTACHING THE STRAP
1. Insert the small loop at the end of the strap under
the Strap Holder. (Fig. 1
2. Insert the other end of the strap through the loop to
tie the strap onto the Strap Holder. (Fig. 1
INSERTING THE BATTERIES
The camera will not operate unless the batteries are in-
stalled. Make sure that the batteries are installed
rectlv.
1.
2.
3.
4.
*
a coin in the slot of the Battery Compartment
Cover to open it. (Fig. 2)
Slide the inner cover latch in the direction indicated
to open. (Fig. 3)
Insert the recommended’ 3 volt lithium batteries,
checking that the + and are inserted correctly.
(Fig. 4)
Press down the inner cover to close.
Close the Battery Compartment Cover by pushing it
in the direction indicated
it locks firmly in place.
(Fig. 5)
Do not remove the batteries from the camera until
you are ready to replace them.
2. When batteries are exhausted, the symbol
will blink in the LCD Panel. Replace with new batter-
ies.
As the battery voltage is reduced in extremely cold
temperatures, the symbol may blink. You may
be able to use the camera if you remove the batter-
ies and warm them up.
In the following cases, battery voltage is insufficient
and the batteries need lo be replaced.
1) When the power does not turn on.
2) When the symbol blinks.
3) When the shutter does not release.
4) When film advance or rewind do not function.
5) When the Self-Timer does not function.
To avoid tripping the shutter inadvertently and wast-
ing battery power, always turn the power off when
you are not taking pictures.
If the camera is not operated (buttons, dials and le-
ver) for about 5 minutes, the power automatically
turns off, the LCD Panel display disappears and the
lens returns to the storage position. The purpose of
this function is to prevent waste of battery power.
The power will turn on again by operating any of the
buttons, dials or lever.
Always avoid direct sunlight when loading the film.
LOADING THE FILM
Push the Back Cover Latch downward to open.
(Fig. 7)
19