Nikon Total Station DTM-322 Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 185

background image

4

Applications

86

Total Station DTM-322 Instruction Manual

The instrument calculates and then records the center of the circle.

It also calculates the coordinates of the center
point and the radius of the circle.

5.

To record the point, press

[ENT]

or the

OK

softkey.

Sample records

SS,71,1.5000,37.0518,32.08380,81.06510,11:51:48,
CO, PT1, 0.0000, 0.0000,47.05350, 83.58560
CO, PT2, 0.0000, 0.0000, 29.53010, 83.58560
CO,O/S MSR:71 1.5555 36.5418 38.28360 81.06510
CO,Radius of circle 0.356
CO,Input +SD:0.0020

Extending the slope distance

1.

To enter the function for extending the slope
distance, press

[8]

or select

Input dSD

in the

Offset menu.

If you have not taken a distance measurement
before entering this function, a temporary
measurement screen appears.

2.

Enter the slope distance that you need to add or
subtract. You can enter any value from
–99.990 t99.990 m (–328.000 through
+328.000 ft).

3.

To record the point, press

[ENT]

.

Sample records

SS,83,1.5000,77.0518,62.08380,81.06510,11:51:48,
CO,O/S MSR:83 1.5555 76.5518 62.08380 81.06510

The calculated point (center of the circle) is stored as an SS record.
The following one or two comment records are angle-measured points.
For example: CO, Point name (fixed to PT1/ PT2), HT(0.0000), SD(0.0000), HA, VA.
If you press the

+SD

softkey before you sight Edge1, the input value is recorded at the end.

«
...
98
99
100
101
102
...
»

Содержание Total Station DTM-322


























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Total Station DTM-322

Бренд: Larson Davis Страницы: 193

Бренд: Facom Страницы: 116

Бренд: Kawai Страницы: 8

Бренд: Endress+Hauser Страницы: 88

Бренд: Stübbe Страницы: 12

HYDROMETTE HB 30

Бренд: GANN Страницы: 65

Бренд: Fly Henry Страницы: 5

Бренд: Interacoustics Страницы: 60

Alta Site Survey Tool

Бренд: Monnit Страницы: 15

Бренд: CAS Corporation Страницы: 20

Ratio:Guard Advanced

Бренд: H.E. Anderson Страницы: 9

Бренд: GW Instek Страницы: 91

Бренд: R&S Страницы: 43

Бренд: Rayleigh Instruments Страницы: 6

NomaSense CO2 P2000

Бренд: NOMACORC Страницы: 12

Бренд: T&D Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Medical International Research Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды