Nikon NPL-302 Series Скачать руководство пользователя

Страница: 226 / 234

Error Messages

206

Pulse Laser Station NPL-302 Series Instruction Manual

Angle

10.1

STN Setup has to be in F1/F2

101.1

You selected

ANG>F1/F2

without an F1/F2 measurement in Station Setup.

Press any key to return to the previous screen. Then go to Station Setup and take
F1/F2 measurement to the BS.

Cogo

10.2

NO Result

102.1

The system was unable to calculate an area because points were not entered in the
correct order.

Press any key to return to the Cogo menu. Then enter the points in the correct order.

Same Coordinate

102.2

The point or coordinate that you entered is identical to the previous input point.

Press any key to return to the point input screen. Then use a different point.

XY-coordinate is required

102.3

The input point does not have XY (NE) coordinates.

Press any key to return to the point input screen. Then enter a point that has X and
Y coordinates.

Communications

10.3

If an error is detected during uploading of data, the instrument aborts the upload
process and displays one of the following messages.

Check Data

103.1

There are errors in the uploaded data. The uploaded data contains errors, such as an
alphabetic character in a coordinate field.

Press any key. Then check the specified line in the data.

DUPLICATE PT

103.2

The uploaded data contains a duplicate PT.

Press any key. Then check the specified point in the data.

Содержание NPL-302 Series











































































































































































































































Результаты поиска

Содержание NPL-302 Series

Отзывы:

Похожие инструкции для NPL-302 Series

Бренды по названию

Популярные бренды

Nikon NPL-302 Series, Инструкция по эксплуатации

Результаты поиска

Содержание NPL-302 Series

Отзывы:

Похожие инструкции для NPL-302 Series

Бренды по названию

Популярные бренды