Nikon LS-2000 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 9

Nikon LS-2000 Скачать руководство пользователя страница 9

9

can include death by electrocution, poisoning by ingestion of lubricants and solvents, blindness by
exploding components, laser LEDs, and not wearing safety glasses, and irreversible and expensive
damage to any and all equipment, computer, tools and instruments.

V. Reference

Major chips on circuit board, where this information is copyright by Nikon Corp, Tokyo, Japan.
CoolScan is a registered trademark. LS-30 S/N are 258340, 233527, 246184

circuit board

P/N F178045-1101-1 , components single-sided, mostly surface mount passive

components, era 2000 date codes
BIOS chip Firmware = 30, soldered-in
main chips:
Nikon EI-104 vE17 main controller
Hitachi HD6413003F16 H8/3003  microcontroller
Analog Devices AD9220AR  12-bit A/D converter
Analog Devices AD7528JR  8-bit D/A converter
LSI Symbios 53CF92A

SCSI controller

WinBond W24257AJ-15ns  memory x8
JRC 7809A  voltage regulator
high quality capacitors are metal encased

CCD Signal Processing board on sensor assy
P/N F17045-1102-1   small subassy with orange 10 wire connector
Stepper Motors X-axis NN-251

Power Supply:

Zebra C7D14-4001C switching power supply
Fuse 3.15A ceramic in-line soldered-in
Regulator chips 5 each
Mitsubishi M51995AFP on reverse of board
UR1 voltage adjust pot

Copyright © August 2007, Phil Lee & Associates, Minneapolis, Minnesota, USA,
[email protected]

«
...
7
8
9

Содержание LS-2000










Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды