Nikon HQA46480 Скачать руководство пользователя

Страница: 182 / 185

Error Messages

168

Total Station DTM-322 Instruction Manual

OVER RANGE

100.24

You are trying to record a coordinate with more than 13 digits

Press any key to return to the previous screen. Then check the current ST coordinate.

Searching

PT Not Found

100.25

There is no point that matches the criteria you entered.

Press any key to return to the point input screen.

This message may appear in any function where the PT/CD is input, such as Station
Setup or Stakeout.

Settings

Job Settings will be changed

100.26

You have changed one or more of the following job settings:

•

VA zero or HA in the Angle screen (see

Angle, page 104

)

•

Scale, T-P, Sea Lvl, or C&R in the Distance screen (see

Distance, page 104

)

•

Coord or Az Zero in the Coordinates screen (see

Coordinate, page 107

)

•

Angle, Dist, Temp, or Press in the Unit screen (see

Unit, page 108

)

Note – To record a point using the new settings, create a new job using the new
settings.

Stakeout

Input Error

100.27

The point name style used in the Fr field is not the same as the style used in the To
field. For example, the Fr field style is 1, and the To field style is A200.

Press any key to return to the Fr/To input screen. Then re-enter the point name, using
the same naming style in both fields.

To ...

Press ...

discard the changes to the job settings

[ESC]

or the

Abrt

softkey. The current job

remains open.

close the current job and save the changes to
the job settings

[ENT]

or the

softkey

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды