Nikon HQA46480 Скачать руководство пользователя

Страница: 122 / 185

Menu Key

108

Total Station DTM-322 Instruction Manual

Unit

To open the Unit menu, press

[7]

or select

Unit

in the

Settings menu.

Recording

To open the Rec menu, press

[8]

or select

Angle

in the

Settings menu.

Angle

DEG (Degree)

GON (GON)

MIL (Mil6400)

Distance

Meter/US-Ft/I-F

If you select US-Ft or I-Ft, an additional settings screen appears. Use this
screen to specify whether to display values in Decimal-Ft or
Ft-Inch.

Temp

°C (Celsius)

°F (Fahrenheit)

Press

hPa/mmHg/inHg

The Angle, Distance, Temp, and Press job settings cannot be changed once a job is created.

Store DB

RAW/XYZ/RAW+XYZ

This setting determines whether raw and/or
coordinate data is stored when you record SS,
CP, or SO records in the Basic Measurement
Screen (BMS) or Stakeout screen.

Data Rec

Internal/COM

Set this field to COM to output data on the COM
port when you press

[ENT]

in the BMS or a

Stakeout screen. The data is not stored to the
job file. For more information, see

Outputting

data to the COM port, page 78

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды