Nikon HQA46480 Скачать руководство пользователя

Страница: 178 / 185

Error Messages

164

Total Station DTM-322 Instruction Manual

Angle

STN Setup has to be in F1/F2

100.1

You selected

ANG>F1/F2

without an F1/F2 measurement in Station Setup.

Press any key to return to the previous screen. Then go to Station Setup and take
F1/F2 measurement to the BS.

Cogo

NO Result

100.2

The system was unable to calculate an area because points were not entered in the
correct order.

Press any key to return to the Cogo menu. Then enter the points in the correct order.

Same Coordinate

100.3

The point or coordinate that you entered is identical to the previous input point.

Press any key to return to the point input screen. Then use a different point.

XY-coordinate is required

100.4

The input point does not have XY (NE) coordinates.

Press any key to return to the point input screen. Then enter a point that has X and
Y coordinates.

Communications

If an error is detected during uploading of data, the DTM-322 instrument aborts the
upload process and displays one of the following messages.

Check Data

100.5

There are errors in the uploaded data. The uploaded data contains errors, such as an
alphabetic character in a coordinate field.

Press any key. Then check the specified line in the data.

DUPLICATE PT

100.6

The uploaded data contains a duplicate PT.

Press any key. Then check the specified point in the data.

CAUTION – If the existing point is a UP, CC, or MP record, and is not referred by ST or BS,
then it will be overwritten by the uploaded record. No error message appears.

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды