Nikon HQA46480 Скачать руководство пользователя

Страница: 143 / 185

Total Station DTM-322 Instruction Manual

129

Menu Key

[S-O]

key settings

To enter the Stakeout settings screen, press

[4]

or select

[S-O]

in the 1sec-Keys menu.

There are two Stakeout settings. For more information,
see

Stakeout, page 107

[DAT]

key settings

To change the settings for the

[DAT]

key, press

[5]

or select

[DAT]

in the 1sec-Keys menu.

The asterisk (*) indicates the currently selected
view format.

To move the cursor, use

[^]

[v]

To change the format displayed by

[DAT]

, press

[ENT]

Calibration

Use the Calibration screen to calibrate the instrument.
To open the Calibration screen, press

[7]

or select

Calibrat.

on the MENU screen.

For more information, see

Adjusting, page 134

Time

Use the Date & Time screen to set the current date and
time.

To open the Date & Time screen, press

[8]

select

Time

on the MENU screen.

The current date and time settings are displayed.

Enter the date in Year-Month-Day format. For
example, to change the date to June 18, 2002,
press

[2] [0] [0] [2] [ENT] [6] [ENT] [1] [8] [ENT]

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды