Nikon HQA46480 Скачать руководство пользователя

Страница: 148 / 185

Checking and Adjustment

134

Total Station DTM-322 Instruction Manual

Rotate the instrument 180° and flip the telescope to the Face-2 position.

Read the vertical angle from the VA2 field.

Add the two vertical angles together, VA1 + VA2.

–

No adjustment is required if the zero reference for vertical angles (VA
zero setting) is set to Zenith, and VA1 + VA2 equals 360°.

–

No adjustment is required if the zero reference for vertical angles (VA
zero setting) is set to Horizon, and VA1 + VA2 is either 180° or 540°.

–

An adjustment is required if VA1 + VA2 is not one of the values listed
above.

Note – The difference between the vertical angle reading the relevant angle (either
360° for Zenith, or 180° or 540° for Horizon) is called the altitude constant.

Adjusting

To enter the calibration screen, press

[MENU]

and

[7]

The DTM-322 has vertical axis adjustment only.
Take an F1 measurement to a target on the
horizon. Press

[ENT]

The vertical angle is shown in the
V0 dir= Horiz setting.

When you have taken the measurement, the
message on the bottom line changes from

NOT TOUCH!

Turn to F2

Take an F2 measurement to the same target.
Press

[ENT]

VA1

Face-1 vertical angle (tilt-off value)

HA1

Face-1 horizontal angle (tilt-off value)

Tilt

Face-1 Y axis tilt value

VA2

Face-2 vertical angle (tilt-off value)

HA2

Face-2 horizontal angle (tilt-off value)

Tilt

Face-2 Y axis tilt value

Содержание HQA46480


























































































































































































Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды

Nikon HQA46480, Инструкция по эксплуатации

Результаты поиска

Содержание HQA46480

Отзывы:

Похожие инструкции для HQA46480

Бренды по названию

Популярные бренды