Nikon FCA54001 Скачать руководство пользователя | Manualshive

Страница: 53 / 57

background image

FCA54001-R.3567.A

- R3 • One Touch Zoom 90s AF -

Item

Standard of judgment

Method and tools

Lens barrel
unit

Eccentricity

·The clearance between the lens barrel and front
cover must be 1/2 or less of the difference
between the maximum and minimum parts.
Check the clearance between the lens barrel and
front cover.

Pin gauge

Driving noise

·It  must  be  58dB  or  less  at  average  sound
pressure.Abnormal  noise  must  not  occur  during
operation.Measure  noise  in  45°  at  a  position
20cm away from the lens front surface.

Lens barrel abnormal
stop

·There must be 400g or more in the upward
position.Set the lens barrel upward and put a
special gauge on it.

Special gauge

Automatic
exposure

AE accuracy

AE tester
Power supply(1)

·The camera must meet the following
conditions in ISO100, 200, 400 and 800.
·Unexposed photography must not occur.
Application range A
WIDE: 6 ≦ Ev ≦ 15.0
TELE: 6 ≦ Ev ≦ 17.0
Error: +2.0 ～ -1.0Ev
Difference: 1.5Ev
Neighboring  difference:  Reverse  must  not  occur
every 1.5Ev.
Application range B
WIDE: 15.0<Ev ≦ 16.0
TELE: 17.0<Ev ≦ 18.0
Error: +2.5 ～ -1.5Ev
Difference: 2.0Ev
Neighboring  difference:  Reverse  must  not  occur
every 2.0Ev.
Error: Error of each measured value obtained by
continuous 3 measuring operations
Difference:  Difference  between  the  maximum  and
minimum values obtained by continuous 3 measur-
ing operations
Neighboring  difference:  Average  value  obtained
by  measuring  the  neighboring  exposure  values  3
times continuously

FM accuracy

Application range A: 4.94 ≦ F ≦ 11.31
Error: +2.0 ～ -1.0Av
Difference: 1.5Av
Neighboring difference: Reverse must not occur
every 1.5Av.
Application range B: 11.31 ≦ F ≦ 16.00
Error: +2.3 ～ -1.3Av
Difference: 1.8Av
Neighboring difference: Reverse must not occur
every 1.8Av.

AE tester
Power supply(1)

Speed light

Guide number

·Gno.: 10 (ISO100·m)±0.5Ev
·Point and line: Gno.7.1 or more

Measure the guide number at a position
1.97m away from the speed light whole

surface. (From film surface: 2m)

JC II flash
Meter IV
Power supply(1)

Light division
characteristics

·At 28° in the right and left direction
and 20° in the up and down direction,
within -1Ev against the image center

JC II flash
Meter IV
Power supply(1)

Recycling time

·8 seconds or less
Release occurs after 8 seconds since winding
ended.

Power supply(1)
Stop watch

«
...
51
52
53
54
55
...
»

Содержание FCA54001


























































Отзывы:

Нет отзывов

Похожие инструкции для FCA54001

PowerShot SX210 IS

Бренд: Canon Страницы: 180

PowerShot SD430 DIGITAL ELPH WIRELESS

Бренд: Canon Страницы: 7

PowerShot SD630 Digital ELPH Camera

Бренд: Canon Страницы: 137

Бренд: Canon Страницы: 2

Бренд: T-Eye Страницы: 23

ENVIROMUX-IPCAM-NPOE

Бренд: NTI Страницы: 5

Бренд: CamPro Страницы: 14

Roadrunner 530A5GPS

Бренд: Prestigio Страницы: 7

Бренд: Grundig Страницы: 98

Бренд: Kodak Страницы: 2

Бренд: Grundig Страницы: 17

MONOFOCAL LENS TC2814NI

Бренд: Tokina Страницы: 1

Бренд: Balluff Страницы: 45

Бренд: OPTRON Страницы: 36

EASYSHARE DX3700

Бренд: Kodak Страницы: 86

Бренд: Zeiss Страницы: 41

Бренд: Roadmaster Страницы: 2

NVC 1000 Series

Бренд: Inscape Data Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды