Nikon ECLIPSE 80i Скачать руководство пользователя страница 57

Страница: 57 / 72

Chapter 4 Assembly

Installing an Epi-illumination attachment

(1)

Place an Epi-illumination attachment on the

microscope arm and fix it with a screw at the
front of the arm.

(2)

Secure in place with two screws at the back of

the Epi-illumination attachment.

(3)

Attach a screw hole protection sticker

provided with the system to the bolt hole.

(4)

Attach a mercury lamphouse to the bayonet

mount on the back. (For more information,
refer to the instruction manual provided with
the super high-pressure mercury lamp power
supply.)

1) Attach a collector lens to the lamphouse.

2) Turn the bayonet mount clockwise (viewed

from the back) as far as it will go.

3) Insert the lamphouse into position.

4) Turn the bayonet mount anticlockwise

(viewed from the back) to lock the
lamphouse.

5) Attach a mercury lamp.

6) Connect the mercury lamphouse to the

mercury lamp power supply.

(5)

Attach the eyepiece tube.

(6)

Attach the eyepiece by aligning the projection

of the eyepiece tube sleeve with the notch at
the objective.

Screws to fix the Epi-illumination

attachment (three screws in total)

Eyepiece tube

Mercury

lamphouse

Eyepiece attached in place

Projection

Notch

Bayonet mount

Eyepiece tube fixing screw

Eyepiece

Содержание ECLIPSE 80i









































































Результаты поиска

Содержание ECLIPSE 80i

Отзывы:

Похожие инструкции для ECLIPSE 80i

Бренды по названию

Популярные бренды

Nikon ECLIPSE 80i, Инструкция по эксплуатации

Результаты поиска

Содержание ECLIPSE 80i

Отзывы:

Похожие инструкции для ECLIPSE 80i

Бренды по названию

Популярные бренды