Nikon COOLPIX S2 VAA36001 Скачать руководство пользователя страница 82

Страница: 82 / 90

VAA36001-R.3667.A

- R7･ S2 -

Item

Criteria

Applied tool(s)

Quality of image

（

～

）

・

The resolution must be in compliance with the following value in

the whole zoom area.
Center horizontal/vertical:

950

TV pcs.

・

Measure the TV resolution pieces at center.

・

Check each posture and the difference of zoom reciprocation.

EIAJ chart
Photoshop
Siemens chart

Resolution in "Macro"

・

Center horizontal/vertical:

950

TV pcs.

・

Check the resolution in near distance (W

cm, M (Z

)

cm and

cm).

・

Take a picture at the high image quality mode.

EIAJ chart
Photoshop
Siemens chart

In the case of
compelling infinity

・

The resolution must be in compliance with the following value in

the whole zoom area.
Center horizontal/vertical:

950

TV pcs.

・

Take a picture of the infinity collimator image at the landscape

mode/image quality priority mode under the "out of focus"
condition by using the

3000

K viewer. (This condition should be

applied to only the product which uses the Q

3035

lens barrel.)

・

Then, open the recorded image data file through Photoshop and

check the resolution visually.

Infinity chart

In the case of "out of
focus"

・

The resolution must be in compliance with the following value in

the whole zoom area.
Center horizontal/vertical:

950

TV pcs.

・

Measure the TV resolution pieces at center.

・

Check each posture and the difference of zoom reciprocation.

・

Put a chart at the distance of

m, set it in the "out of focus"

condition and shoot it.

EIAJ chart
Photoshop
Siemens chart

Gradation/luminance
level

<Histogram's gray average value>

・

Black:

Gray:

140

White:

215

・

Equip the

5100

K viewer with a scale and shoot an object in the

full range of angle of view while the AUTO mode and the image
quality priority mode are set.

・

Open the recorded image data file through Photoshop and pick up

a measurement section with the each color (its central area

pixels) with the rectangle selector tool.

・

Read the histogram's gray value and the gray standard deviation.

・

Measurement section

Luminance level:
Upper left

step: Black,

steps: Gray, Center: White

Lower left

steps: Gray,

steps: Black

5100

K viewer

ITE

Gray scale (standard)
Photoshop

Содержание COOLPIX S2 VAA36001


























































































Результаты поиска

Содержание COOLPIX S2 VAA36001

Отзывы:

Похожие инструкции для COOLPIX S2 VAA36001

Бренды по названию

Популярные бренды

Nikon COOLPIX S2 VAA36001, Руководство по ремонту

Результаты поиска

Содержание COOLPIX S2 VAA36001

Отзывы:

Похожие инструкции для COOLPIX S2 VAA36001

Бренды по названию

Популярные бренды