
EN nv
Niko
sa Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: [email protected] — www.niko.eu
PM350-41750BR18051_EN
350-41750 / 350-41751 / 350-41760 / 350-41761 / 350-41780 / 350-41781
6
4. IR REMOTE CONTROL
To programme the detector, the (optional) remote control 350-41934 must be used (see Fig. 9).
The detector must be unlocked for setting all configurations except “Status”, “1”, “2”, “3”, “4”, “On/Off”, “Auto”, “Dim +” and “Dim –”. The detector is automatically locked after five minutes after the last time a button is
activated. The detector can also be locked manually. Any changes to settings will be saved. During programming, the green LED briefly switches off to acknowledge the correct receipt of information when a button is pushed
on the IR remote control.
5. TECHNICAL DATA
Dimensions surface-mounting models 350-41751, 350-41761 and 350-41781 (see Fig. 4a)
64.1 x 117.3 mm (HxW)
Visible dimensions flush-mounting models 350-41750, 350-41760 and 350-41780 (see Fig. 4b)
46.4 x 100 mm (HxW)
Dimensions including non-visible part flush-mounting models 350-41750, 350-41760 and 350-41780 (see Fig. 4b)
136.4 x 100 mm (HxW)
Power supply voltage
230 Vac ± 10%, 50 Hz
Power consumption
0.45 W
Relay contact
NO 10 A, 250/400 Vac
Maximum load
incandescent lamps (2,300 W)
230 V halogen lamps (2,300 W)
all low-voltage halogen lamps (1,200 VA)
fluorescent lamps (non-compensated) (1,200 VA)
energy-saving lamps (CLFi) (350 W)
LED lamps with electronic control gear (500 VA)
LED lamps 230 V (350 W)
Maximum capacitive load
140 μF
Maximum inrush current
165 A/20 ms or 800A/200
μ
s
Light sensitivity
100 - 2,000 lux
Switch-off delay
5 mins. - ∞
Mounting height 350-41750, 350-41751, 350-41780 and 350-41781
2 – 3.4 m
Mounting height detectors for heigh ceilings 350-41760 and 350-41761
4 – 8 m
Detection angle
360° (3 x 120°)
Detection range for body movement 350-41760 and 350-41761
circle up to 32 m diameter
Detection range for body movement 350-41750, 350-41751, 350-41780 and 350-41781
circle up to 24 m diameter
Wire input
2 x 2.5 mm²
Protection degree (after mounting)
IP54
Ambient temperature
-5 °C to +50 °C
Integrated EnOcean receiver (only with the 350-41780 and 350-41781)
STM 300
Marking
CE marked in accordance with EN 60669-2-1
Accessories
IR remote control (350-41934)
IR user remote control (350-41935)
6. LED STATUS
LED
Status
Meaning
All LEDs illuminate red, blue, yellow and green alternately
"Out-of-the-box"
The detector is connected but not yet configured.
The green LED lights up continuously
Door unlocked
The detector is in programming mode and is ready for configuration with the (optional) IR remote control.
All LEDS are off
Locked
The detector is locked and the most recently programmed changes are saved.
The red and green LEDs flash on and off for one second
Addressing
The detector is addressing.
The green LED lights up 1 second
Addressing
All luminaires have been addressed.
The green LED flashes
Addressing
The correct zone has been selected.
The green LED turns off for 1 second and the red LED lights up for one second
Addressing
The wrong zone has been selected.
The red LED is flashing
Calibration
The red LED flashes at one-second intervals to indicate that calibration is underway. Only flashes
if the detector is in operating mode.
The red LED flashes upon detection of movement
Walking test sector A
The red LED will flash when activity is detected in sector A.
The green LED flashes upon detection of movement
Walking test sector B
The green LED will flash when activity is detected in sector B.
The blue LED flashes upon detection of movement
Walking test sector C
The blue LED will flash when activity is detected in sector C.
The green LED flashes once
IR remote control (accessory)
Each time the detector receives a correct signal from the (optional) IR remote control, the detector
will acknowledge this by briefly switching off the green LED if the detector is being programmed.
In operating mode, the green LED will flash once.
The green LED flashes for as long as the button is activated
Dim+ or Dim-
The light is dimmed with the remote control
The red LED lights up continuously
2 h ON/OFF
The daylight group flashes twice upon activation of this mode, after which the red LED lights up
as long as the mode is activated
The yellow LED flashes continuously
Burn in
The yellow LED flashes on and off for one second when the function is active.
The yellow and red LEDs flash continuously
Replacing or adding DALI Control Gear
This means more DALI Control Gear have been added or more than one defective DALI control
has been replaced.
7. POWER CONSUMPTION
The maximum power consumption of the integrated DALI power supply is 200 mA. This value must not be exceeded. Keep this in mind when adding DALI components.
We give an overview of the maximum power consumption of several common DALI components below:
Component
Maximum power consumption
Luminaire 1
2 mA
Dimmer potentiometer
6 mA
DALI slave (e.g. 350-41752 or 350-41753)
5.5 mA
DALI slave for high ceilings (e.g. 350-41762)
5.5 mA
DALI push-button interface 350-70020
6 mA
DALI module 350-70021 for connecting adjacent zones
14 mA