①
Mount indicator securely, such as on optional Magnetic
Base, and make sure that the Spindle is perpendicular
to the measurement surface.
②
Press [MODE] or [SET] to turn on power.
③
Setting 0-Point.
＜
REL Mode
＞
With gauge in contact with reference surface, press the
[SET] button.
Display will read
“
0.00mm.
”
＜
ABS Mode
＞
With gauge in contact with reference surface, press the
[MODE] button. When display reads
“
SEt
”
, press the
[SET] button. (ref.
“
Function Setup - Preset Function
”
)
Display will read
“
0.00mm.
”
※
If
“
0.00mm
”
is not displayed, please refer to
“
Function
Setup - Preset Value
”
to set value to 0.00mm, and then
perform steps
①
to
③
.
④
With Gauge body held fixed, and the probe in contact
with the workpiece, the LCD will display the difference
between workpiece and reference plane.
●
●
●
●
●
●
●
●
●
This is a precision instrument, handle with care. Do not
drop or subject to excessive forces.
Keep away form high voltage and strong magnetic fields;
instrument damage may result.
Do not use or store in direct sunlight or locations with
high temperatures such as in a car, or near a stove or
heat source.
When taking measurements, hold gauge securely, such
as in magnetic base. (sold separately)
Please do not disassemble or modify.
Remove dust and cutting chips after use and apply rust
preventative oil to metallic surfaces. Please keep out of
reach of children.
Do not use organic solvents to clean the body of the
instrument.
When not being used for a long period of time, please
remove battery.
Only use as directed. Improper use may cause accident
or injury.
※
If no operation is performed after 5 seconds, display
will return to the measurement screen.
【
ABS / REL Mode
】
※
This function not available.
【
Preset Value
】
Numerical value can be preset,
and later called up to
measurement screen.
ABS
【
Measurement Direction
】
【
Measurement Screen
】
Switchable between ABS or REL
modes.
＜
ABS mode
＞
●
Press [SET] Button to hold the
displayed reading. Press once
and
“
H
”
icon will show, and value
will hold. Press again to release.
＜
REL mode
＞
●
At any probe position, press the
[SET] button to call up and
display the Preset Value.
(see
“
Preset Value
”
below)
【
Preset Function
】
Preset Value set can be called
up for display.
※
For use in ABS, or REL mode.
【
Resolution
】
※
DEI-233S2 only
I299-K
1604
Niigata seiki Co., Ltd.
6-15-22, Tsukanome, Sanjo, Niigata, Japan, 955-0055
Tel. : +81-256-31-5670 Fax. : +81-256-39-7730
MAIL [email protected]
URL http://www.niigataseiki.co.jp
HOW TO USE
Press the [MODE] button to cycle through the functions in
the sequence shown below. When desired function is
displayed, press [SET] button to access the various settings.
FUNCTION SETUP
CAUTION
Press [MODE] to display ABS / REL,
then press [SET] to select.
To Set
Press [MODE] to move cursor, and
press [SET] to change value.
To Set
Press [MODE] to display
“
Inc
”
(+) /
“
dEc
”
(-), then press [SET] to select.
To Set
Press [MODE] to display 0. 01 / 0. 001,
then press [SET] to select.
To Set
[MODE] Button
[MODE] Button
[MODE] Button
[MODE] Button
[MODE] Button
[MODE] Button
[MODE] Button
【
Power ON
】
Press [MODE], or [SET] button to turn on power.
【
Power OFF
】
Press and hold the [SET] button to turn off power.
※
Power will switch off automatically if idle after
approximately 4 hours.
(
※
REL Mode only)
※
When battery level is low, the
『
』
icon is displayed;
please replace battery.
POWER
B
