Larson Electronics, LLC. • 9419 US-HWY 175 • Kemp, TX 75143 • 1-800-369-6671 • 1-903-498-3363 • www.larsonelectronics.com
EXPRA-08R-LED
•
While keeping the left-hand tabs in their
slots, gently press down on the right side of the
cover until the two right-hand tabs slip into their
respective slots. (Image 11)
one way. It is not possible to install it in a
reversed position.
The Non-Rechargeable
Battery Carrier is ready to install into the Angle
Light. Installation of the Non-
Rechargeable Battery Carrier into the Angle Light
is the same as installing the Lithium-
ion Battery Pack. Please see the instructions listed above in the
LITHIUM-ION RECHARGEABLE BATTERY PACK
section.
PLACING THE ANGLE LIGHT INTO THE CHARGER
The charger is designed to securely hold a properly installed EXPRA-08R-
LED Angle Light in place under conditions up to and including 9g of lateral
force meeting the requirements of NFPA 1901 (2009).
WARNING: Installing the Angle Light into the charger MUST be done
using the following steps. Failure to do so could damage the charger
or its ability to hold the Angle Light securely in place.
The spring-loaded grips located on the charger, are designed to snap
around the body of the light one at a time…not simultaneously.
•
While positioned in front of the charger, grasp the Angle Light around
the bezel and place either the left or right side of the light into the charger
at an approximate 45 degree angle being certain that the base of the light
rests on the base contour of the charger. (Image 12)
•
While holding the inserted side of the light against the back of the
light (allowing the edge to slide around the contour of the charger) until it
slips past the Spring-loaded Gripper and snaps into the charger. (Image
13)
WARNING: Attempting to push the Angle Light straight into the
charger or from an angle above or below, could result in damage to
the charger and should not be attempted.
Indicator Light. When the Angle Light is properly installed in the charger,
and power is being supplied by the AC or DC Power Supply, the LED
Charge Indicator Light on the charger will light up constant RED indicating
that the unit is being charged. (Image 14)
REMOVING THE ANGLE LIGHT FROM THE CHARGER
•
While positioned in front of the charger, grasp the Angle Light around
the bezel and twist it in either a clockwise or counter-clockwise direction.
(Image 15)
Image 17
•
This action will cause the side of the light to disengage from the charger
and slip past the Spring-loaded Gripper. (Image 16)
•
While maintaining an approximate 45 degree angle to the light, pull the
light straight away from the charger. (Image 17)
•
The light has now been safely removed from the charger and is ready
to use.
CHARGING THE ANGLE LIGHT
WARNING: Use only the supplied Charger, Lithium-ion Rechargeable
Battery Pack and AC or DC Power Supply for charging. Do not
attempt to charge this light with non-rechargeable or rechargeable AA
batteries installed.
•
The time required to charge the Angle Light is conditional on the
remaining charge left in the Lithium-ion Rechargeable Battery Pack at the
time of charging. The maximum charge time required is approximately 6
hours.
•
use, or if the Lithium-ion Rechargeable Battery Pack has been unused for
several months.
•
Install the Angle Light into the charger using the exact method described
in this Instruction Manual above (“
PLACING THE ANGLE LIGHT INTO
THE CHARGER”
).
WARNING: Failure to do so could damage the
charger and/or the light.
•
When the Angle Light is properly seated in the charger, the LED
Charge Indicator light will turn solid RED indicating that the Lithium-
ion Rechargeable Battery Pack is charging (Image 14). The Lithium-
ion Rechargeable Battery Pack is fully charged when the LED Charge
Indicator light turns GREEN.
•
The Lithium-ion Rechargeable Battery Pack does not have any
Recharge Memory Effect, therefore placing the Angle Light in the charger
prior to full depletion of the battery does not adversely affect the battery
negative impact on the battery or the battery life.
OPERATION
THE
HAS EIGHT SEPARATE LIGHTING
MODES:
•
High-brightness Flashlight
•
Medium-brightness Flashlight
•
Survival-mode Flashlight
•
Flashlight Strobe
•
High-brightness Floodlight
•
Medium-brightness Floodlight
•
Survival-mode Floodlight
•
Dual-Light (both the Flashlight and Floodlight
on at the same time)
Flashlight Modes
To activate the Flashlight, press and release the Flashlight Switch
(Image 18). The default mode will be High-brightness. To select the
brightness level for the Flashlight, press and hold the Flashlight Switch.
up again at a rate of approximately one mode per second. The light will
continue to cycle up and down through the various modes as long as the
switch is held down. When the desired brightness level is reached, simply
release the Flashlight Switch, and the light will remain in that brightness
mode. To turn the Flashlight off, press and release the Flashlight Switch
one more time.
Strobe
To activate the Strobe, double click the Flashlight Switch (Image 18). To
turn the Strobe off, press and release the Flashlight Switch one more time.
Floodlight Modes
To activate the Floodlight, press and release the Floodlight Switch
(Image 18). The default mode will be High-brightness. To select the
brightness level for the Floodlight, press and hold the Floodlight Switch.
up again at a rate of approximately one mode per second. The light will
continue to cycle up and down through the various modes as long as the
switch is held down. When the desired brightness level is reached, simply
Image 11
Image 12
Image 13
Image 14
Image 15
Image 16
Image 18
