Before using your NightSearcher product, please read this user manual. It contains important
safety information and operating instructions. Following this advice will help ensure that your
product operates to its maximum potential.
Light Output
600 lumen
Light Source
Cree XLAMP XM-L LED
Running Time
1.5h+ (100%) / 15h (10%)
Charge Time
6h
Battery
18650 2200mAh Lithium lon rechargeable
Product Size (mm)
L172 x Dia.48
Product Weight (kg)
0.282
NS Part No
NSEXPLORERXML
Supplied with
Flashlight, battery and mains charger
The Cree® XLAMP XM-L LEDs can last 50, and seldom needs to be replaced. If there is
any malfunction of LED, please contact Nightsearcher Limited or an authorised distributor.
INSTALLING THE BATTERY
Unscrew the tail cap.
Insert the battery pack into the barrel. This battery can be inserted either end first
Fasten the tail cap tightly.
BATTERY CHARGING
Turn the flashlight to the OFF; connect the charger to the charging socket of the
flashlight.
Connect the charger to AC power supply; the LED indicator (located on the charger)
will turn RED.
When the battery is fully charged, the LED indicator will turn GREEN.
Disconnect the charger from the AC power supply and then disconnect the charger
from the flashlight.
NOTE: This flashlight is powered by Lithium-Ion rechargeable battery. This battery will not
reach its optimum performance until three charging cycles are completed. Please charge it
for 12 hours before first use.
The ON/OFF switch is located in the tail of the flashlight
Press the ON/OFF switch once: 100% intensity
Press and hold the ON/OFF switch a second time: 10% intensity
Press and hold the ON/OFF switch a third time: dimmable (100%-5%)
STROBE AND SOS
In OFF, press and hold the ON/OFF switch for 2 seconds, the flashlight will blink
Press and hold the switch for 2 seconds again for SOS flash mode
NOTE: In any mode, press the ON/OFF switch once to switch the flashlight OFF.
Use a small brush or blow dry air to clean any dust inside the reflector.
Use lens cleaner and cotton swab, to remove any fingerprints on the lens.
To prevent the O-ring from drying and to ensure threads operate smoothly, please
apply petroleum jelly to these surfaces two or three times a year.
The non-anodised metal groove between the tail cap and the barrel must be cleaned
periodically to ensure a good electrical contact.
The O-ring prevents water from getting into the flashlight.
Do not use the flashlight for diving; it is not suitable for the high pressure underwater
environment.
If water gets inside the flashlight, remove the battery immediately and place in a well
ventilated area.
Please read the instructions below before charging the flashlight:
BATTERY
Before using the flashlight for the first time, or if you have not used it for a long time,
you need to fully charge the flashlight for 12hrs.
Do not expose the battery to excessive heat, to do so may cause an explosion.
Do not use metal objects to short circuit the positive and negative end of the battery.
Do not dispose of the battery in the domestic waste, please use the correct method of
disposal.
Do not solder directly on to the battery.
Do not let the battery become wet or immerse the battery in water.
If there is evidence of leakage from the battery do not touch the battery with bare
hands. If your skin or your clothes come into contact with any leaked substance from
the battery, clean with water immediately.
Should any leaked substance from the battery come into contact with your eyes, do
not rub your eyes, rinse with clean water immediately and seek medical assistance as
soon as possible.
Keep the battery away from children.
The operating temperature range of the flashlight’s battery is listed below :
- Charging: 0°C to 45°C / Discharging: -20°C to 60°C
GENERAL
The instructions hereunder list the safety measures for operating your flashlight and
charger:
Do not use any chargers other than those provided. Failure to do so could cause fire,
electrical shock or personal injury
Never use a damaged charger or charger with damaged lead. Should the charger or
its lead become damaged, replace the charger immediately.
Do not shine the flashlight directly into people’s eyes, as it may damage their eyesight.
If the charger is not in use, please disconnect it from the AC power supply. Do not
leave the battery on charge for more than one week as this will shorten the battery
life. Battery leakage may occur if the battery is over charged.
Do not pull the lead of the charger when disconnecting it from the AC Power supply.
Do not use an extension lead. Connect the charger directly into an electrical socket.
Always make sure the flashlight system is disconnected from any power sources and
turned off when performing any routine cleaning or maintenance. Do not try to repair
the unit or charger yourself.
In case of any problems or questions please contact Nightsearcher Limited or an
authorised distributor.
FLASHLIGHT MAINTENANCE
SAFETY PRECAUTIONS
ON / OFF AND MODE OPERATION
BATTERY INFORMATION
LED INFORMATION
SPECIFICATION
