WARNING
Onced Armed, Cutting,
Jumpering or Removing the Loop
or Contact Wires,
sets off the alarm.
The Limpet can only be
deactivated using the
Supplied Key
NO or NC Contact Closures for
Connection to any Contact
Closure Device.
Central Burglar System, AMX®
Crestron® Control Devices,
or Video Cameras etc.
1. Remove the cover's (4) 4.40 Tamper Proof Screws.
using the T8 Tamper Proof Hex Key.
2. Form a Loop with the Supplied 4 ft Cable, or use your own. (See Note)
3. If using our Loop wire, select either Red, Black, Green or White Wire.
4. Make a hole in the Grommets to allow the Wire to pass through.
5. With the selected Colored Wire, connect the formed Loop to the Euro Connection
(See Below if using the Keep Method).
6. You can either cut or discard the other Wires as they are not needed.
The Loop Wire consists of 4 Conductor Wires. The
Installer chooses only one of the four to form the Loop.
The idea of 4 different Wires is to make it more difficult
for a thief to chose the actual wire to cut.
SUPPLIED PARTS
GENERAL INSTRUCTIONS
Replacement Batteries are available from Most Hardware Stores including ACE, True Value etc,under the Brand Name, Ultalife
or 10 Year 9v Battery. Replacement Loop Wire or Keys etc., are freely available from us at reasonable cost.
Nigel B Design, Inc. California, USA. Tel: (818) 487-9323 Fax: (818) 766-9805
Web Site: www.nigelbdesign.com. E-Mail: [email protected]
REPLACEMENT BATTERIES & PARTS
The User can also use any Wire or
Length for the Loop, depending
on the needs of the actual
installation
SPECIFICATIONS
Built in Siren: 117 db
Current Consuption: 1000th of 1 mAmp
Battery:10 Year Ultralife 9v Lithium
Dimensions 4" x 2" x 1.5". Weight: Less than 7ozs
FOR SECURITY REASONS
We deliberately chose components that cannot compromise
the security aspects of the Limpet™ such as the Arming Key
and Tamper Proof Screw Hex Key. Thieves will find it impossible
to find these in any Hardware Store.
Optional
Mounting Holes
(If not using the
supplied Glue)
10 Year 9 V Battery
117 Db Siren
(Runs up to 30 Hours
when Limpet is Activated)
Removable Red Plug
Disables Siren
for Silent Mode
Key Switch
Connection
PLEASE NOTE
When setting up allow at least
one minute between
Key Arming and Disarming
T8 Tamper Proof Key
4 ft Loop Wire
Hardened Steel Loop Keep
10 Year 9 Volt Lithium Battery
Two Special Pattern
Arming/Disarming Keys
One Tube Plastic Welder
TWO METHODS OF USING THE LIMPET TO PROTECT THE DEVICE
THE KEEP METHOD.
1. Spead a small amount of Plastic Welder to the Keep.
2. Immediatly Press and clamp the Keep to the Device.
DEVICE METHOD
THE PLASTIC WELDER- A WARNING
Plastic Welder is a Bonding Medium used to “weld” the Limpet or Keep to any device that
needs to be protected. Once Bonded the user should be aware that it is almost impossible
to remove the devices that have been bonded. For this reason the Keep Method should be
used if removal of the Projector or Device is contemplated.
1. Spread a small amount of Plastic Welder to the Limpet.
2. Immediatly Press and clamp the Limpet to the Device.
NC
NO
COM
LOOP
When you are using a Contact Connection
.
1. Determine if you want NC or NO Closure Connection or both.
2. Select the Wire you want to use, and connect it to the Euro connector on the Circuit Board
3. Make a hole in the Grommet to allow the Wire to pass through.
(If you do not want to use the Built in Siren, simply remove the Red Plug).
If you want to mount the Limpet using Screws or Bolts.
1. Remove the 2 Pan Head Screws that holds the Piezo Siren down.
2. Screw or Bolt the Limpet to a Fixed Part of the Structure or to the Device.
3. Replace the Piezo Alarm.
4. Install the Battery.
5. Replace the Cover.
6. Arm the Unit with the Supplied Key once it is Glued or Bolted .
