background image

If a tube needs to be installed in the tire, check first for the possible damages. Round it onto

the rim. Make sure to keep the tube in the right position throughout the mounting process.

To install the upper tire bead, place the tire well and readjust position of the tire bead

(same as mount of the lower tire bead in Fig.26-B. Press down the tire opposite to the
mount/demount head to the rim groove (Fig.27)

Depress the pedal D (Fig.20) to turn the turntable while keeping pressing on the tire. When

only 10~15cm is left, slow down to avoid damage of the tire bead. Stop the motor if there is
any indication for damage. Lift the pedal D and turn the turntable counter-clockwise. Try again
when the tire is back to the original shape.
Note: It is not necessary to move the handle of the screw every time if the size of rim matches
the tire. Just move the arm.
In the process of operation, keep head and hands away from the area between the tire and the
swing arm to avoid injury.

Inflating Tire

Danger

!!

Inflating can be highly dangerous. Take precautions and pay close attention to the

procedures. Check if the compressed air is well connected before inflating.

Inflating procedures are shown in Fig.28. The
machine is equipped with a gauge to read the
pressure in the tire.

Connect the outlet of the gun to the air

inflation valve

Slowly press the switch on the inflating gun

for several times during inflation to make sure
that the reading on pressure gauge meets the
manufacturer’s specifications. The pressure
should not exceed 3.5 bar.

If the pressure exceeds the limit, press the button on the gun inflator so that the pressure

goes down to what is required.

Fig.28

Fig

.

26

Fig.27

Содержание CT2880

































Отзывы:

Похожие инструкции для CT2880