Nidec LAROY-SOMER LSA 44.3 Скачать руководство пользователя страница 13

Страница: 13 / 28

2018.01 / g

Electric Power Generation

Installation and maintenance

LSA 44.3

Low Voltage Alternators - 4 pole

5056 en -

4.5 - Electrical faults

Fault

Action

Effect

Check/Cause

No voltage

at no load on

start-up

Connect a new

battery of 4 to 12

volts to terminals

E- and E+,

respecting the

polarity, for 2 to 3

seconds

The alternator builds up and

its voltage is still correct

when the battery is removed

- Lack of residual magnetism

The alternator builds up but

its voltage does not reach

the rated value when the

battery is removed

- Check the connection of the voltage reference

to the AVR

- Faulty diodes

- Armature short-circuit

The alternator builds up but

its voltage disappears when

the battery is removed

- Faulty AVR

- Field windings open circuit (check winding)

- Revolving field coil open circuit (check the

resistance)

Voltage too

low

Check the drive

speed

Correct speed

Check the AVR connections (AVR may be faulty)

- Field windings short-circuited

- Rotating diodes burnt out

- Revolving field coil short-circuited

- Check the resistance

Speed too low

Increase the drive speed (do not touch the AVR

voltage pot. (P2) before running at the correct

speed)

Voltage too

high

Adjust AVR

voltage

potentiometer

Adjustment ineffective

Faulty AVR

Voltage

oscillations

Adjust the

AVR stability

potentiometer

If no effect: try normal or fast

stability

modes (ST2)

- Check the speed: possibility of cyclic

irregularity

- Loose connections

- Faulty AVR

- Speed too low when on load (or AVR LAM set

too high)

Voltage

correct at no

load and too

low when on

load

Run at no load and

check the voltage

between E+ and

E- on the AVR

Voltage between E+ and E-

(DC)

SHUNT < 20V - AREP / PMG

< 10V

- Check the speed (or AVR LAM set too high)

Voltage between E+ and E-

SHUNT > 30V - AREP / PMG

> 15V

- Faulty rotating diodes

- Short-circuit in the revolving field coil. Check

the resistance.

- Faulty exciter armature. Check the resistance

Voltage

disappears

during

operation

Check the AVR,

the

surge suppressor,

the rotating

diodes, and

replace any

defective

components

The voltage does not return

to the rated value

- Exciter winding open circuit

- Faulty exciter armature

- Faulty AVR

- Revolving field coil open circuit or short-

circuited

Содержание LAROY-SOMER LSA 44.3





























Результаты поиска

Содержание LAROY-SOMER LSA 44.3

Отзывы:

Похожие инструкции для LAROY-SOMER LSA 44.3

Бренды по названию

Популярные бренды

Nidec LAROY-SOMER LSA 44.3, Руководство по установке и обслуживанию

Результаты поиска

Содержание LAROY-SOMER LSA 44.3

Отзывы:

Похожие инструкции для LAROY-SOMER LSA 44.3

Бренды по названию

Популярные бренды