Nidec Digitax HD M753 EtherCAT Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 262

Nidec Digitax HD M753 EtherCAT Скачать руководство пользователя страница 37

Digitax HD M753 Control User Guide

37

Issue Number: 3

5.4

Menu 0

Menu 0 is used to bring together various commonly used parameters for
basic easy set up of the drive. The parameters displayed in Menu 0 can
be configured in Menu 22.
Appropriate parameters are copied from the advanced menus into
Menu 0 and thus exist in both locations.
For further information, refer to Chapter 6

Basic parameters

Figure 5-8 Menu 0 copying

5.5

Advanced menus

The advanced menus consist of groups or parameters appropriate to a
specific function or feature of the drive. Menus 0 to 41 can be viewed on
the Remote Keypad RTC.
The option module menus (S.mm.ppp) are only displayed if option
modules are installed. Where S signifies the option module slot number
and the mm.ppp signifies the menu and parameter number of the option
module’s internal menus and parameter.

Table 5-5 Advanced menu descriptions

* Only displayed when the option modules are installed.

5.5.1

KI-Remote Keypad set-up menu

To enter the keypad set-up menu press and hold the escape

button on the keypad from status mode. All the keypad parameters are
saved to the keypad non-volatile memory when exiting from the keypad
set-up menu.

To exit from the keypad set-up menu press the escape

or

or

button. Below are the keypad set-up parameters.

Menu 0

00.004
00.005
00.006

Menu 2

02.021

Menu 1

01.014

Menu 4

04.007

5
0

150

0

150

5

Menu

Description

0

Commonly used basic set up parameters for quick / easy
programming

1

Frequency / Speed reference

2

Ramps

3

Frequency slaving, speed feedback and speed control

4

Torque and current control

5

Motor control

6

Sequencer and clock

7

Analog I/O

8

Digital I/O

9

Programmable logic, motorized pot, binary sum, timers and
scope

10

Status and trips

11

Drive set-up and identification, serial communications

12

Threshold detectors and variable selectors

13

Standard motion control

14

User PID controller

15

Option module slot 1 set-up menu

16

Option module slot 2 set-up menu

17

Option module slot 3 set-up menu

18

General option module application menu 1

19

General option module application menu 2

20

General option module application menu 3

21

Second motor parameters

22

Menu 0 set-up

23

Not allocated

25

Option module slot 1 application parameters

26

Option module slot 2 application parameters

27

Option module slot 3 application parameters

29 Reserved

menu

30

Onboard user programming application menu

31-41

Advanced motion controller set-up parameters

Slot 1

Slot 1 option menus**

Slot 2

Slot 2 option menus**

Slot 3

Slot 3 option menus**

«
...
35
36
37
38
39
...
»

Содержание Digitax HD M753 EtherCAT







































































































































































































































































Отзывы:

Нет отзывов