Nidec COMMANDER S100 Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 118

background image

Getting started

66

Commander S100 User Guide

7.3.2 Menu 2 - Reference & ramps

This menu groups together parameters used for speed control and configures how the drive accelerates and decelerates to the chosen reference by
the ramp system. Four frequency references can be configured, and the user can switch between these using digital inputs or via communications to
provide the drive with a final frequency reference.

Frequency Reference Configuration

(P0.05) can be used to automatically configure the multiple

references and the required control terminal functions. Alternatively, setup the four references using the parameters

Frequency Reference 1 Selector

(P2.21) to

Frequency Reference 4 Selector

(P2.24).

Figure 7-2 Menu 2 - Reference & ramps

Reference Switch Bit 0 and Reference Switch Bit 1

can be selected as functions of the drive control terminals and use a binary system to switch

between references as Table 7-1 describes.

Table 7-1 Frequency reference switch

Alternatively, Frequency

Reference 1 to 4 Switch

(P2.20) can be used to select individual references.

Reference Switch Bit 1

Reference Switch Bit 0

Reference Selected

0

0

Frequency Reference 1

0

1

Frequency Reference 2

1

0

Frequency Reference 3

1

1

Frequency Reference 4

P2.01

Minimum Frequency Limit

Range:

0.0 to 300.0 Hz

Default:

0.0 Hz

Sets the minimum limit applied to the selected reference. If the value set is higher than the

Maximum Frequency Limit

(P2.02) the reference will be

limited to the maximum. This limit is used for both directions of rotation.

P2.02

Maximum Frequency Limit

Range:

0.0 to 300.0 Hz

Default:

Region Dependent

Sets the maximum limit applied to the selected reference. Generally, the motor rated frequency is used as the maximum frequency limit.
This is a symmetrical limit for both directions of rotation.
This is used for scaling the range of percentage inputs.
Default for 50 Hz regions = 50.0 Hz
Default for 60 Hz regions = 60.0 Hz.

Output Frequency

(P1.01) can be higher than this limit due to motor slip compensation.

NOTE

«
...
64
65
66
67
68
...
»

Содержание COMMANDER S100























































































































Отзывы:

Нет отзывов

Похожие инструкции для COMMANDER S100

Бренд: SOMFY Страницы: 27

ECI-42 K1 Series

Бренд: ebm-papst Страницы: 28

CMMT-AS-C12-11A-P3-EC-S1

Бренд: Festo Страницы: 16

Бренд: SilverStone Страницы: 2

Бренд: Hitachi Страницы: 13

Бренд: Hitachi Страницы: 25

Бренд: Hitachi Страницы: 2

Бренд: KB Electronics Страницы: 20

Бренд: LSIS Страницы: 81

External DVD - External DVD Optical Drive

Бренд: Iomega Страницы: 18

Бренд: ZIEHL-ABEGG Страницы: 24

Бренд: Vaidnor Страницы: 296

Бренд: E-Z Anchor Puller Страницы: 19

Бренд: E.H. Wachs Страницы: 42

Бренд: Melec Страницы: 42

Бренд: Danfoss Страницы: 81

VLT HVAC Series

Бренд: Danfoss Страницы: 338

Gemini GT6 Series

Бренд: Parker Страницы: 81

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды