Nidec COMMANDER S100 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 118

background image

Getting started

Commander S100 User Guide

55

7.2 Single line parameter descriptions

The lists below contain all parameters within the drive and states the possible settings of the parameter with the default value. For further description
of the parameters refer to section 7.3

Parameter descriptions

or use the Marshal app.

7.2.1 Menu 1 - Status & monitoring (Read-only)

The lists in this table are for reference only and do not include sufficient information for adjusting these parameters. Incorrect
adjustment can affect the safety of the system and damage the drive and or external equipment. Before attempting to adjust any
of these parameters, refer to section 7.3

Parameter descriptions

.

Parameter

Range

P1.01

Output Frequency

± Maximum Frequency Reference

(P2.02) Hz

P1.02

Output Voltage

0 to Maximum Output Voltage V

(110 V, 200 V Drive = 240 V, 400 V Drive = 480 V)

P1.03

Output Power

Drive Rating Dependent kW

P1.04

Motor RPM

±18000 rpm

P1.05

Drive State

Inhibited (0), Ready (1), NA (2), NA (3), Running (4), Supply Loss (5), Deceleration (6), Injecting DC (7),

NA (8), Error (9), NA (10), NA (11), NA (12), NA (13), NA (14), Under Voltage (15)

P1.06

Output Current

± Drive Rated Current x 2.2 A

P1.07

Torque Producing Current

± Drive Rated Current x 2.2 A

P1.08

Percentage Load

± Torque Current Maximum Limit %

P1.09

Alarm Indicators

00000000 to 11111111

P1.10

Drive Status Indicators

00000000 to 11111111

P1.11

Sequencer Input and Output Indicators

00000000 to 11111111

P1.12

Run & Direction Indicators

00000000 to 11111111

P1.13

Ramp Input

± Maximum Frequency Reference

(P2.02) Hz

P1.14

Ramp Output

± Maximum Frequency Reference

(P2.02) Hz

P1.15

T2 Analog Input 1 Percentage

±100.00 %

P1.16

T4 Analog Input 2 Percentage

±100.00 %

P1.17

T15 Frequency Input Percentage

±100.00 %

P1.18

Up/Down Percentage

0.0 to 100.0 %

P1.19

PID Output Percentage

±100.00 %

P1.20

PID Status Indicators

00000000 to 11111111

P1.21

PID Error

±100.00 %

P1.22

Motor Thermal Percentage

0 to 100 %

P1.23

Drive Thermal Percentage

0 to 100 %

P1.24

DC Bus Voltage

0 to Maximum D.C. Bus Voltage V

(110 V, 200 V Drive = 415 V, 400 V Drive = 830 V)

P1.25

Digital IO Indicators

00000000 to 11111111

P1.26

Parameter 1 Saved Value on Error

Dependent on parameter saved

P1.27

Parameter 2 Saved Value on Error

Dependent on parameter saved

P1.28

Parameter 3 Saved Value on Error

Dependent on parameter saved

P1.29

Error

0 to 255

P1.30

Error History 1

0 to 255

P1.31

Error History 2

0 to 255

P1.32

Error History 3

0 to 255

P1.33

Drive Diagnostic

0 to 17

WARNING

«
...
53
54
55
56
57
...
»

Содержание COMMANDER S100























































































































Отзывы:

Нет отзывов

Похожие инструкции для COMMANDER S100

VLT Midi Drive FC 280

Бренд: Danfoss Страницы: 96

VLT Midi Drive FC 280

Бренд: Danfoss Страницы: 66

Liquid-Cooled Adaptive Frequency AFDE

Бренд: Trane Страницы: 60

Бренд: IEF Werner Страницы: 48

Бренд: D+H Страницы: 2

Бренд: CENTENT Страницы: 48

Pavilion t100 - Desktop PC

Бренд: HP Страницы: 2

Бренд: HP Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 80

Бренд: Philips Страницы: 88

Бренд: MRMC Страницы: 20

Бренд: Targus Страницы: 4

Бренд: Lincoln Electric Страницы: 45

PowerFlex 755TM

Бренд: Rockwell Automation Страницы: 120

Бренд: Sanyo Denki Страницы: 119

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды