Nidec COMMANDER S100 Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 118

background image

Technical data

114

Commander S100 User Guide

10.12 IP rating

The drive is rated to IP20 pollution degree 2 (non-conductive contamination only). The IP rating of a product is a measure of protection against
ingress and contact to foreign bodies and water. It is stated as IP XX, where the two digits (XX) indicate the degree of protection provided as shown in
Table 10-8.

Table 10-8 Rating descriptions

Table 10-9 UL enclosure ratings

10.13 Vibration

Bump Test

Testing in each of three mutually perpendicular axes in turn.
Referenced standard: IEC 60068-2-27: Test Ea:
Severity: 15 g peak, 11 ms pulse duration, half sine.
No. of Bumps: 18 (3 in each direction of each axis).
Referenced standard: IEC 60068-2-29: Test Eb:
Severity: 18 g peak, 6 ms pulse duration, half sine.
No. of Bumps: 600 (100 in each direction of each axis).

Random Vibration Test

Testing in each of three mutually perpendicular axes in turn.
Referenced standard: IEC 60068-2-64: Test Fh:
Severity: 1.0 m²/s³ (0.01 g²/Hz) ASD from 5 to 20 Hz
-3 db/octave from 20 to 200 Hz
Duration: 30 minutes in each of 3 mutually perpendicular axes.

Sinusoidal Vibration Test

Testing in each of three mutually perpendicular axes in turn.
Referenced standard: IEC 60068-2-6: Test Fc:
Frequency range: 5 to 500 Hz
Severity: 3.5 mm peak displacement from 5 to 9 Hz
10 m/s² peak acceleration from 9 to 200 Hz
15 m/s² peak acceleration from 200 to 500 Hz
Sweep rate:1 octave/minute
Duration: 15 minutes in each of 3 mutually perpendicular axes.
Referenced standard: EN 61800-5-1: 2007, Section 5.2.6.4. referring to IEC 60068-2-6:
Frequency range: 10 to 150 Hz
Severity: 0.075 mm amplitude from 10 to 57 Hz
1g peak acceleration from 57 to 150 Hz
Sweep rate:1 octave/minute
Duration:10 sweep cycles per axis in each of 3 mutually perpendicular axes.

First Digit

Second Digit

Protection against foreign bodies and access to hazardous parts

Protection against ingress of water

0 Non-protected

0 Non-protected

1 Protected against solid foreign objects of 50 mm ø and greater (back
of hand)

1 Protected against vertically falling water drops

2 Protected against solid foreign objects of 12.5 mm ø and greater
(finger)

2 Protected against vertically falling water drops when enclosure tilted up
to 15°

3 Protected against solid foreign objects of 2.5 mm ø and greater (tool)

3 Protected against spraying water

4 Protected against solid foreign objects of 1.0 mm ø and greater (wire)

4 Protected against splashing water

5 Dust-protected (wire)

5 Protected against water jets

6 Dust-tight (wire)

6 Protected against powerful water jets

7 -

7 Protected against the effects of temporary immersion in water

8 -

8 Protected against the effects of continuous immersion in water

UL Rating

Description

Type 1

Enclosures are intended for indoor use, primarily to provide a degree of protection against limited amounts of falling dirt.

Type 12

Enclosures are intended for indoor use, primarily to provide a degree of protection against dust, falling dirt and dripping non-
corrosive liquids.

«
...
112
113
114
115
116
...
»

Содержание COMMANDER S100























































































































Отзывы:

Нет отзывов

Похожие инструкции для COMMANDER S100

Бренд: ABB Страницы: 24

Бренд: ABB Страницы: 13

Бренд: NEC Страницы: 26

Бренд: NEC Страницы: 16

Бренд: NEC Страницы: 18

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 9

Бренд: NEC Страницы: 11

Бренд: Toshiba Страницы: 6

H802A - SD - Disk Drive

Бренд: Toshiba Страницы: 1

Бренд: Toshiba Страницы: 12

Бренд: Toshiba Страницы: 12

Бренд: Toshiba Страницы: 16

Бренд: Toshiba Страницы: 12

Бренд: Toshiba Страницы: 12

Бренд: Toshiba Страницы: 12

Бренд: Toshiba Страницы: 16

C2402 - SD - DVD-ROM Drive

Бренд: Toshiba Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды