Page 11
DUPLEX KEY AREA :
EDIT area
[DELETE]
* Delete the chase or chase step during programming
* Press one time to delete the current chase step.
* Keep pressing 3 seconds to delete all steps of current
* [SET X/U]- Press [DELETE] to cancel the X-Y channel assignment.
View previous steps during programming
Save current chase steps or view nest edited step during programming
[SET X/Y]
Active programming,press [SET X/Y] and select X/Y channel between CH1-24 of
scanner via SA/SB/SC to assign X/Y channel to joystick. Press [SET X/Y] again to save
and quit setting when yellow indicate led ON.
[CLEAR]
* Press [CLEAR] to delete selected number key at once the number key can be
selected repeat during program running.
* In the running mode, all channel data will be cleared to zero after pressing this key
RUN area
[CROSS MODE]
*MODE1: All channel fade time be controlled by Cross slider during program running
*MODE2: The edited X/Y channel fade time be controlled by Cross slider but all other
channel run in jump way to prevent unedited color or gobos from playing during slow
program running
[RUN SECNE]
During chase running, press [RUN SECNE] and P1-P24 TO SELECT FIRST 24 steps
of Chase 1&2 to run as special steps alone. Press [RUN SCENE] again to quite this
function and then current chase will continue to run
[RELEASE CHANNELS]
* Under MANUAL mode, Press [RELEASE CHANNELS] and move sliders of selected
channel by pressing SA/SB/SC or Joystick to change CH1-CH24 output data during
program current data of selected channel. Press [RELEASE CHANNELS] again to quit
this function
* O indicates the CH1-24 channel data is controlled by manual slider, and F indicates
Program run as preset data automatic
[MANUAL]
During chase running, press [ Manual ]& any key of(p1-p20) to select the scanner want
to be controlled manually and then move sliders of relative channel to control it
manually. Then control selected scanner in auto and manual at the same time.
ECRAN LCD :
Display
Specific information
XXXXXX XXXX
Model and version number
S/N: 0020-02-2727****
TEST OK
Series Number and Test condition
RUN Chase [??] CH[**] [***]
or X→ [***] Y[***]
The upper line shows current running chase and bottom line indicates current modified channel
number and channel data.
RUN SCENE SELECT P1--
P24
* Press P1 to P20 to select 20 steps of 1
st
chase
* Press P21-P24 to select 1
st
4 steps of 2
nd
chase
EDIT Chase[??] Step [01]
[**]
Press [EDIT/RUN] and then corresponding indicate light ON to enter EDIT situation
[??]-- Edit chase number
STEP [01]-- Chase step number, modify it with
or
[**]-- current step is last step of edit chase. There will no number if it has data already
EDIT Chase [??] CH [**] or
X→ [***] Y [***]
The upper line shows current edit chase number and the bottom line represents the modified channel
number and channel data.
EDIT Chase [??] SPEED
[***] or CROSS [***]
The upper line represents the chase number to be edited and bottom line indicates current modified
chase running speed or cross time
12345678
FFFFFFFF A
Or FFFFFFFF B
Or FFFFFFFF C
*Press [RELEASE CHANNELS] under MANUAL mode to get left menu
*FFFFFFFF A--Show 1-8 channel status
*FFFFFFFF B --Show 9-16 channel status
*FFFFFFFF C--Show 17-24 channel status
* Press SA/SB/SC to select relative channel and move sliders of it to change status
Set: X-Y
X: [] Y:[]
Press [EDIT] and [SET X/Y], select scanner by P1-P20 ( Set X/Y for all scanner if not select scanner
by P1-P20), press SA/SB/SC to select relative channel to assign to joystick or press [DELETE] to
delete previous assignment setting
