www.nicolaudie.com
Sunlite Touch-sensitive Intelligent Control Keypad
Ref. STICK-KE2
© Nicolaudie-Sunlite 1989-2019. All rights reserved. We reserve the right without notice to amend the technical information and specifications.
ESA Pro Software (Windows) - Ti Multi-Zone
https://www.nicolaudie.com/esapro.htm
ESA2 Software (Windows/Mac) - Single Zone
www.nicolaudie.com/esa2.htm
Hardware Manager (Windows/Mac) - Firmware, clock..
www.nicolaudie.com/download.htm
Page 4
V 1.9
P1 P2 P3 P4 ... GND
Make a cable using the 3 pins : TX, RX and G (GND)
Set the RS232 parameters to : 9600bds 8 bits, no Parity, 2 Stop bits
- To play a scene, send 3 bytes :
1 x 255
- To stop a scene, send 3 bytes :
2 x 255
- To pause a scene, send 3 bytes :
3 x 255
- To release a pause, send 3 bytes :
4 x 255
- To reset a scene, send 3 bytes :
5 x 255
The scene number (x) can be from 1 to 40. For instance, 11 means
Page B Scene #3
The controller can be connected to a local network, allowing it to be
controlled from a smartphone or tablet over WiFi.
• Connect the controller to a router or switch with an RJ45 cable
• The controller is set by default to get an IP address from the
router via DHCP. If the network is not working with DHCP, a
manual IP address and subnet mask can be set using the
Hardware Manager
• If the network has a filewall enabled, allow port 2430
The dmx controller can be connected to an existing automation
system over a network and triggered via UDP packet on port 2430.
Use HardwareManager to find IP address of dmx controller. Refer to
the remote protocol document for more information.
Stick 1 Remote Protocol (PDF)
www.nicolaudie.com/download.htm
Dry Contact Port Triggering
Network Control
UDP Triggering
A relay can be connected between the RELAY and GND sockets of
the 20 pin extension socket. This is an OPEN COLLECTOR OUTPUT
that can drive up to 150mA, 20V. Current flows when the controller
is on and is stopped when in standby.
It can be used to turn off other equipment such as lighting drivers to
save power (see diagram right).
RS232 Triggering
It is possible to start scenes using the input ports (contact closure).
To activate a port, a brief contact of atleast 1/25 second must be
established between the ports (1...8) and the ground (GND). Note:
the scene will not be switched off when the switch is released
.
Relay
Example relay : FINDER Ref. 22.23.9.012.4000
Technical datasheet Revision date 10 Jan 2019
The controller be programmed from a PC, Mac, Tablet or
Smartphone using the software available on our website. Refer
to the corresponding software manual for more information. The
firmware can be updated using the Hardware Manager which is
included with the programming software.
Programming the Controller
Setting up the Controller
The controller can be used with one of 3 different apps.
Lightpad
Designed to work seamlessly with the controller, Lightpad provides
an easy way to control your lights over a local WiFi network from a
tablet or smartphone. Use the slider to change the dimmer, color or
speed, and the 8 scene buttons to select scenes and effects just like
the wall panel.
www.nicolaudie.com/lightpad.htm
Easy Remote
Create an entirely customized remote controller for your tablet or
smartphone. Easy Remote is a powerful and intuitive app allowing
you to easily add buttons, faders, color wheels and more. Connect to
a WiFi network and the app will find all compatible devices.
www.nicolaudie.com/easy-remote.htm
Arcolis (Android only)
The Arcolis application is a comprehensive tool allowing you to
directly control and re-program the controller from your smartphone
or tablet. This is a simple application which can be used by just about
everyone in any situation. Mobile, easy to use and powerful, Arcolis
is the ideal controller for dimming or switching traditional, LED and
RGB color mixing DMX lighting fixtures. Program static and dynamic
lighting scenes and effects.
iPhone/iPad/Android Control
