NI CB-2162 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 23

NI CB-2162 Скачать руководство пользователя страница 17

©

National Instruments Corporation

17

NI CB-2162 User Guide

Mounting the NI CB-2162 in an Enclosure

You may want to mount the NI CB-2162 in an enclosure to reduce radio
interference or for convenience when using the NI CB-2162 in a
rack-mount system.

You can purchase a CA-1000 (777664-01) and an NI CB-2162 CA-1000
Mounting Kit (192065-01) for mounting your NI CB-2162 in an enclosure.
The mounting kit contains a VHDCI panelette and three screws. The
CA-1000 includes the standoffs that are required to attach the NI CB-2162
to the bottom of the CA-1000.

If you want to rack-mount the NI CB-2162 after it is installed in the
CA-1000, you can purchase rack-mount side panels (777665-01).

To install the NI CB-2162 in the CA-1000, complete the following steps:

1.

Remove the jackscrews and washers from the NI CB-2162
DDC connector, as shown in Figure 10.

Figure 10.

Remove Jackscrews from DDC Connector

Note

You will not need the washers to mount the NI CB-2162 in the CA-1000. Save the

washers in case you ever need to remove the NI CB-2162 from the CA-1000 and use the
NI CB-2162 outside the enclosure.

1

Jackscrews

2

Washers

3

NI CB-2162

3

2

1

«
...
15
16
17
18
19
...
»

Содержание CB-2162
























Отзывы:

Нет отзывов