NF FRA5014 Скачать руководство пользователя страница 32

Страница: 32 / 107

3.1 Panel Components and Operations

FRA5014

3-2

3.1 Panel Components and Operations

The following describes the names and operations of components on the

FRA5014

’s front and rear

panels.

Figure 3-1. Front Panel

<1> Power switch

Press this switch upward to turn the power on and downward to turn it off.

<2> POWER lamp

This lamp is on when the power is on.

<3> OSCILLATOR lamp

This lamp is on when the oscillator is on.

<4> MEASURE lamp

This lamp is on during measurements.

<5> CALIBRATION lamp

This lamp is on during self calibration.

<6> ERROR lamp

This lamp is on during when a command error, output overcurrent, overload input

voltage, self calibration error, or self test error has been detected.

When an error query remote command such as “SYST:ERR?” is received, the error

queue is emptied and the error lamp goes off. If an output overcurrent or an overload

input voltage is detected, the error clear remote command “SYST:OVER:REL” will

cause the error lamp to go off, but error messages may remain in the error queue.

<1>

<3> <4> <5> <6>

<2>

Содержание FRA5014












































































































Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды

NF FRA5014, Инструкция по эксплуатации

Результаты поиска

Содержание FRA5014

Отзывы:

Похожие инструкции для FRA5014

Бренды по названию

Популярные бренды