nextys DCW20 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 35

nextys DCW20 Скачать руководство пользователя страница 20

DCW20

User Manual rev. 5

Page 20/34

Symbol Name

Function

MENU KEY

Scrolls between menus.

DOWN KEY

Scrolls down menus and values.

UP KEY

Scrolls up menus and values.

OK KEY

Confirms selection.

Table 5: User interface key

4.1 Status

The status screen shows the measurement and statuses to ease the system diagnostic. The screen is
divided in sections identified by the symbols shown below:

Input

: The measured input voltage and current is shown in this section.

Output

: The measured output voltage and current is shown in this section.

Battery

: The battery voltage, current, temperature, resistance and charge are shown in this

section. During charging and discharging the symbol background color changes to orange and
the number of bars drawn inside reflects the charge status. During discharging and charging
an arrow drawn beside the symbol reflects the direction of the current flowing through the
battery, pointing towards the battery during charging. Battery section is not present in DC/DC
mode.

Auxiliary

: The measured auxiliary output voltage and current is shown in this section.

For each section the icon background color reflects its status, green on healthy state or red/orange
otherwise.
Furthermore, in case of alarm a message appears on the screen after 60s of inactivity (no key
pressed).

Figure 11: UPS status screen

Figure 12: DC/DC status screen

Figure 13: Alarm screen

4.2 Settings

The setting menu contains all the  configurable parameters available to the user. Use the UP/DOWN
KEY  to  navigate  through  the  menu  items.  Press  the  OK  KEY  to  enter  and  exit  the  editing  mode,
exiting  the  edit  mode  stores  and  activates  the  new  configuration.  While  in  editing  mode  use  the
UP/DOWN  KEY  to  change  the  selected  value.  All  settings  are  also  accessible  via  Modbus  at  the
specified address. All the battery related settings are ignored in DC/DC operating mode.

DCW20_040-02-700-005-EH-1117

«
...
18
19
20
21
22
...
»

Содержание DCW20




































Отзывы:

Нет отзывов