Nextar ncd90 Скачать руководство пользователя страница 14

13

Auxilliary in, 

RCA out &

Subwoofer out

Auxiliary Input

The Auxiliary Input Jack is on the pan-

el of the unit. Insert the AUX IN cable's 

stereo plug into the AUX IN jack on the 

panel of the unit. Route the other end 

of  the  stereo  plug  to  the  headphone 

jack of any external audio device such 

as  walkman  and  discman.  Press  the 

Mode button to choose AUX. Connect 

any  portable  audio  device  such  as  a 

DVD player or VCD player to the AUX 

IN  cable.  Use  the  volume  control  to 

adjust volume.

RCA Output

The RCA Output Jack is on the back 

of the unit. (Refer to Wiring Diagram) 

This output is for connecting amplifier, 

equalizer,  or  other  audio  compone-

ment that requires a pre-amp out con-

nection.  (Red = Right, White = Left)  

Follow the manufacturers instructions 

for the audio component that you are 

connecting.

Subwoofer Output

The Subwoofer Output Jack is on the 

back of the unit. (Refer to Wiring Dia-

gram) This output is for connecting a 

subwoofer amplifier. You must connect 

an amplifier to the Subwoofer Output 

Jack to drive a subwoofer. Follow the 

amplifier's installation instructions. To 

activate subwoofer control, press and 

hold the SEL button, then press SEL 

to cycle to “WOOF OFF”. Then rotate 

the  volume  knob  to  choose  WOOF 

ON”  so  that  the  subwoofer  function 
will be turned on.

ID3 Tag

If  an  MP3/WMA  file  has  ID3  Tag  in-

formation,  it  will  be  displayed  on  the 

LCD.  If  there  is  no  ID3  Tag  informa-

tion, nothing will shown on LCD. The 

sequence  of  ID3 Tag  information  will 

be shown as follows:

You can also press the BND/ID3 but-

ton on the remote control to view the 

ID3 information anytime. 

 

MAINTENANCE

Cleaning the Unit

Do  not  use  any  liquids  to  clean  this 

unit.

Do  not  use  petroleum  distillates  to 

clean this unit.

Use  a  clean,  dry  cloth  to  clean  this 

unit.

Replacing the Fuse

Make  sure  the  amperage  matches 

the  specified  value  when  replacing 

the  fuse(s).  If  the  fuse  is  bad,  check 

the  power  connection  and  replace 

the fuse with a new one. If the same 

problem occurs, this might indicate a 

malfunction within the unit. 

Warning

When  replacing  a  fuse,  do 

not use a fuse with a higher 

amperage  rating  than  the 

fuse  originally  supplied  to 

your  unit,  otherwise  dam-

age will result to your unit.

(FILE)

(FOLDER)

MUSIC

ALBUM

ARTIST

Содержание ncd90

















Отзывы: