background image

3

4

3 - RADIO PROGRAMMING

This procedure lets you programme compatible multifunctional or generic transmitters.

4 - DELETION OF RADIO

These procedures let you delete from the memory transmitters that have already been programmed.

MULTIFUNCTIONAL TRANSMITTERS

CODES:

HB70-SLCT, HB70-SPCT, 
HB80-1C, HB80-1DIM, HB80-2L, HB80-30D, HB80-30RGBW, HB80-4C, HB80-4DIM, HB80-4L, 
HB90-6LT, 
ROUND-1SP, 
SENSA-M, SENSA-P, SENSA-R35M, SENSA-R35P, SENSA-R35T, SENSA-T, 
TOUCH-1, TOUCH-1CCT, TOUCH-1DIM, TOUCH-1SP, TOUCH-1L , TOUCH-1RGBW, TOUCH-3C, TOUCH-4DIM, TOUCH-CFU

With multifunctional transmitters the transmitter control modes depend on the model used. 

Refer to the transmitter manual, to the paragraph entitled "commands sent by the transmitter", 

bearing in mind that it is an "dimmer" device.

GENERIC TRANSMITTERS (WIRELESS BUS)

CODES:

HB80-6G, 
MCU-TX4, 

TOUCH

-1G, 

TOUCH

-2G, 

TOUCH

-4G, TOUCH-LOCK4, TOUCH-TX2, 

ROUND-1G

With generic transmitters, the transmitter's control modes are:

Short press= On/Off, Long Press= Dimmer Up/Down

PROCEDURE

STEP 1

Press the button 1.

The led turns on.

MAKE A TRANSMISSION

WITH THE TRANSMITTER

MAKE A SHORT

PRESS

MAKE A TRANSMISSION

WITH THE TRANSMITTER

THE LED TURNS ON

MAKE A SHORT

PRESS

THE LED STARTS 

FLASHING QUICKLY 

AND TURNS OFF

STEP 2

Within 60 seconds make a transmission with the 

transmitter to be saved.

See transmitter manual, the paragraph 

entitled "transmitter programming"

for specify information.

The led makes 3 flashes and turns off.

LED MAKES 3 FLASHES

AND TURNS OFF

THE LED STARTS 

FLASHING QUICKLY

AND TURNS OFF

PROCEDURE

STEP 1

Hold the receiver button 1 down (about 8 seconds.) until

the LED begins to flash.

STEP 2A

Within 10 seconds make a transmission with the 

transmitter that you want to delete. 

The LED flashes quickly and turns off.

STEP 2B

Within 10 seconds press the button on 

the receiver for a short time to confirm the 

delection of all transmitters. 

The LED starts flashing quickly and turns off.

PROLONGED PRESS

(about 5 seconds)

LED FLASEHES

DELETION OF 

SINGLE TRANSMITTER

DELETION OF ALL 

TRANSMITTER SAVED

Содержание PLANO-V5/RGBW









Отзывы: