background image

24

STAINLESS STEEL

There are many different stainless steel cleaners 
available. Always use the mildest cleaning procedure 
first, scrubbing in the direction of the grain. Specks of 
grease can gather on the surfaces of the stainless 
steel and bake on to the surface and give the 
appearance of rust. For removal use a mild abrasive 
pad in conjunction with a stainless steel cleaner.

GRILL GRATE

The easiest way to clean the grill is immediately after 
cooking is completed and after turning off the flame. 
Wear a barbeque mitt to protect your hand from the 
heat and steam. Dip a brass bristle barbeque brush in  
water and scrub the hot grill. Dip the brush frequently 
in the bowl of water. Steam, created as water 
contacts the hot grill, assists the cleaning process by 
softening any food particles. If the grill is allowed to 
cool before cleaning, cleaning will be more difficult.

ENSURE THAT THE GAS SUPPLY AND THE 
KNOBS ARE IN THE “OFF” POSITION. MAKE 
SURE  BURNER ARE COOL BEFORE REMOVAL.

GRILL BURNERS

Extreme care should be taken when moving a burner 
as it must be correctly centered on the orifice before 
any attempt is made to relight the grill. Frequency of 
cleaning will depend on how often you use the grill. 

MAIN GRILL BURNER CLEANING

Ensure the gas supply is off and the knobs are in the 
“OFF” position. Make sure the grill is cool. Clean the 
exterior of the burner with a wire brush. Clear stubborn 
scale with a metal scraper. Clear any clogged ports with a 
straightened paper clip. Never use a wooden toothpick as 
it may break off and clog the port. Please note if insects or 
other obstructions are blocking the flow of gas through the 
burner, and if so you will need to call our customer service 
line 

0239-2322880.

GREASE TRAY CLEANING

:

The grease tray should be emptied and wiped down 
periodically and washed with a mild detergent and warm 
water solution. A small amount of sand may be placed in 
bottom of grease tray to absorb the grease. Check the 
grease tray frequently, do not  allow excess grease to 
accumulate and overflow out of the grease tray. 

BURNER CLEANING:

1.

Turn off the gas supply, and make sure all the knobs 
are in the “OFF” position.

2.

Wait for the grill to cool.

3.

Clean the exterior of the burner with a wire brush.  
Use a metal scrapper to stubborn stains.

4.

Clear clogged port with a straightened paper clip. 
Never use a wooden toothpick as it may break off 
and clog the port

5.

If inserts or other obstructions are blocking the flow 
of gas through the burner, call customer service at 
0239-2322880

Care and Maintenance

Содержание 720-0466








































Отзывы: