Nexen 5H100PSE-E Скачать руководство пользователя страница 5

Страница: 5 / 19

FORM NO. L-20255-H-0822

GENERAL SAFETY PRECAUTIONS

WARNING

Ensure proper guarding of the product is
used.  Nexen  recommends  the  machine
builder  design  guarding  in  compliance
with  OSHA  29  CFR  1910  “Occupa-
tional Safety and Health Hazards.”

CAUTION

Watch  for  sharp  features  when
interacting  with  this  product.  The  parts
have  complex  shapes  and  machined
edges.

WARNING

This  product  is  capable  of  emitting  a
spark  if  misused,  therefore  is  not
recommended  for  use  in  any  explosive
environment.

CAUTION

Use appropriate guarding for moving
components. Failure to guard could
result in serious bodily injury.

CAUTION

This product has possible pinch points.
Care should be taken when interacting
with this product.

CAUTION

Use lifting aids and proper lifting
techniques when installing, removing or
placing this product in service.

CAUTION

This product has possible pinch points.
Care should be taken when interacting
with this product.

CAUTION

Use appropriate guarding for moving
components. Failure to guard could
result in serious bodily injury.

Содержание 5H100PSE-E




















Результаты поиска

Содержание 5H100PSE-E

Отзывы:

Похожие инструкции для 5H100PSE-E

Бренды по названию

Популярные бренды

Nexen 5H100PSE-E, Руководство пользователя

Результаты поиска

Содержание 5H100PSE-E

Отзывы:

Похожие инструкции для 5H100PSE-E

Бренды по названию

Популярные бренды