background image

viii

Preface

Copyright © 2013 NEXCOM International Co., Ltd. All rights reserved

nROK 500 User Manual

Safety Precautions

1. 

Read these safety instructions carefully.

2.   Keep this User Manual for later reference.

3.   Disconnect this equipment from any AC outlet before cleaning. Use a 

damp cloth. Do not use liquid or spray detergents for cleaning.

4.   For plug-in equipment, the power outlet socket must be located near 

the equipment and must be easily accessible.

5.   Keep this equipment away from humidity.

6.   Put this equipment on a stable surface during installation. Dropping it 

or letting it fall may cause damage.

7. 

Do not leave this equipment in either an unconditioned environment 
or in a above 40

o

C storage temperature as this may damage the 

equipment.

8.   The openings on the enclosure are for air convection to protect the 

equipment from overheating. DO NOT COVER THE OPENINGS.

9.   Make sure the voltage of the power source is correct before 

connecting the equipment to the power outlet.

10.   Place the power cord in a way so that people will not step on it. Do 

not place anything on top of the power cord. Use a power cord that 
has been approved for use with the product and that it matches the 
voltage and current marked on the product’s electrical range label. 
The voltage and current rating of the cord must be greater than the 
voltage and current rating marked on the product.

11.   All cautions and warnings on the equipment should be noted.

12.   If the equipment is not used for a long time, disconnect it from the 

power source to avoid damage by transient overvoltage.

13.   Never pour any liquid into an opening. This may cause fire or electrical 

shock.

14.   Never open the equipment. For safety reasons, the equipment should 

be opened only by qualified service personnel.

15.   If one of the following situations arises, get the equipment checked by 

service personnel:

 

a. The power cord or plug is damaged.

 

b. Liquid has penetrated into the equipment.

 

c. The equipment has been exposed to moisture.

 

d. The equipment does not work well, or you cannot get it to work    

             according to the user’s manual.
 

e. The equipment has been dropped and damaged.

 

f. The equipment has obvious signs of breakage.

16.  Do not place heavy objects on the equipment.

17.  The unit uses a three-wire ground cable which is equipped with a third 

pin to ground the unit and prevent electric shock. Do not defeat the 
purpose of this pin. If your outlet does not support this kind of plug, 
contact your electrician to replace your obsolete outlet.

18.  

CAUTION

: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY 

REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE 
RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES 
ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.

19.  The computer is provided with CD drives that comply with the 

appropriate safety standards including IEC 60825.

Содержание nROK 500











































Отзывы: