Nexcom NDiS B533 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 68

background image

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved.

35

NDiS B533 User Manual

Chapter 3: System Setup

To mount the system on to a wall or some other surface using the two
mounting brackets, please follow the steps below.

1. Turn the system over, then remove the two screws.

Wall Mounting Instructions

3. Drill holes in the intended installation surface.

4. Align the mounting holes on the sides of the mounting brackets with the

predrilled holes on the mounting surface.

5. Insert four retention screws, two in each bracket, to secure the system

to the wall.

Wall Mount Bracket

Specification of the wall mount screw:
Round Head Screw w/Flat Washer Long Fei
6#32*min. 5.7mm-8mm_w/Flat

2. Align the two retention screw holes in each bracket with the retention

screw holes on the sides of the bottom surface. Secure the brackets to
the system by inserting two retention screws into each bracket.

«
...
47
48
49
50
51
...
»

Содержание NDiS B533





































































Отзывы:

Нет отзывов

Похожие инструкции для NDiS B533

Бренд: Jäger Страницы: 36

F120-H830.02 S9W2V

Бренд: Jäger Страницы: 44

CHALLENGER II Series

Бренд: M&R Страницы: 241

Бренд: Pronomic Страницы: 16

Бренд: Taktomat Страницы: 35

N4-4-S1-PV-NA Series

Бренд: Eaton Страницы: 6

Бренд: Argus Страницы: 58

Бренд: Datacolor Страницы: 3

SIMATIC PC 577B

Бренд: Siemens Страницы: 28

SIMATIC PCIe DIO4

Бренд: Siemens Страницы: 62

SIMATIC PC RI25/45

Бренд: Siemens Страницы: 122

SIMOTION P320-4 E

Бренд: Siemens Страницы: 166

SIMATIC IPC677E

Бренд: Siemens Страницы: 158

SIMATIC Rack PC 840 V2

Бренд: Siemens Страницы: 178

SIMATIC IPC677D

Бренд: Siemens Страницы: 196

SIMOTION P320-4 E

Бренд: Siemens Страницы: 222

SIMATIC IPC647E

Бренд: Siemens Страницы: 200

SIMATIC IPC847E

Бренд: Siemens Страницы: 212

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды