Nexa CURTISS P-40 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 12

Nexa CURTISS P-40 Скачать руководство пользователя страница 8

Plastic control horn

....................3

2x20mm screw

...............6

Securely glue together. If coming off
during flight, you lose control of your
air plane.

Apply a thin layer of machine oil or petroleum jelly to only the pivot point of the hinges on the elevator, then push the
elevator and its hinges into the hinge slots in the trailing edge of the horizontal stabilizer. There should be a minimal
hinge gap.
When satisfied with the and alignment, hinge the elevator to the horizontal stabilizer using 5 minute epoxy. Make sure
to apply a thin layer of epoxy to the top and bottom of both hinges and to inside the hinge slots. Repeat the previous
procedures to hinge the second elevator to the other side of the horizontal stabilizer.

Hinge

Petroleum jelly

STABILIZER

A B

Apply 5 min.
Epoxy both the
top and bottom.

Securely glue together. If coming off during flight,
you lose control of your air plane.

7- Horizontal stabilizer

8- Elevator & Rudder

Install the horizontal stabilizer into the fuselage
and adust the alignment as described in steep
6.

When you are satisfied with the alignment,
with the

thin CA

glue around the top and

bottom of the stabilizer where it meets the
fuselage.

Add a thin layer of 15 minutes Epoxy glue along the horizontal stabilizer to contact
the fuselage to make sure there are no gaps.

A B

A B

15 min. Epoxy

CA

Thin CA glue

«
...
6
7
8
9
10
...
»

Содержание CURTISS P-40













Отзывы:

Нет отзывов